Sri Electronics & Embedded Solutions

With this board you can develop and prototype with any of 8051 40 pin microcontrollers. The RS232 driver on board allows easy connection with PC or other embedded hardware ( Easy to falsh 89v51Rd2 Through flash magic, SST through SST Flasher, Nuvoton through Nuvoton Flasher). The board have User buttons and status LEDs. The bridge rectifire allow this board to be powered with both AC and DC power supply adapters.

 

Product Details:

• RS232 Tx, Rx interface with MAX232 IC on socket
• DIL40 ZIF Socket ( Zero Insertion Force) microcontroller socket.
• Reset button.
• Extension slot on every uC pin with pull up resistor for port0,port1,port2 and port3.
• GND bus.
• Vcc bus.

 

I/O Features:

• Easy to test with Burg Connecters wires.
• A Serial Port for ISP.
• A Serial Port for USB.
• An RS232 Serial Port.
• 7Seg Mulitplexed Display.
• Ready Interface for LCD display 2x16
• 24Cxx I2C EEPROM.
• RTC DS1307.
• 8 LED array.
• 4x4 Matrix Key Pad.
• 4 Interupt Switches.
• ULN2803 To Drive Stepper Motor and Relays.
• L293D TO Drive DC Motors.
• PCF8591 TO Convert analog signal to digital signal with 4 analog channel.
• 1 Relay and 1 Buzzer.
• Eaxample Programs for LED,7seg,LCD,RS232 ,Matrix Key Pad, ADC.
• Easy To flash 89V51RD2 Through Flash Magic Software.

 

Package Content:

• 8051 Development Board ( WITH CHIPS RS232,RTC1307,I2C24c,ULN2803).
• Burg Connecters 20 Nos.
• Software CD( Flash Magic,Data sheets,Example Porograms,Manual,Keil Eva).

Additional Information:

• Item Code: SEES-1054
• Production Capacity: 1000 NOS
• Delivery Time: 1-2 DAYS
• Packaging Details: Carton Boxes

Renesas Starter Kit for RL78 Target Devices - RL78/G12 - 16-Bit Single-Chip Microcontrollers

Features:

• General-purpose register: 8 bits × 32 registers (8 bits × 8 registers × 4 banks)
• ROM: 2 KB to 16 KB, RAM: 256 bytes to 2 KB, data flash memory: ?/2 KB
• High speed on-chip oscillator : 24/16/12/8/4/1 MHz(TYP) can be selected
• On-chip single-power-supply flash memory (with prohibition of block erase/writing function)
• Self-programming
• On-chip debug function
• On-chip power-on-reset (POR) circuit and voltage detector (LVD)
• On-chip watchdog timer (operable with the dedicated low speed on-chip oscillator clock)
• On-chip key interrupt function
• On-chip clock output/buzzer output controller
• On-chip BCD adjustment
• I/O ports: 18/22/26 (N-ch open drain: 2)

Timer:

• 16-bit timer: 4/8 channels
• Watchdog timer: 1 channel
• 12-bit Interval timer: 1 channel

Serial interface:

• CSI: 1/2/3 channel
• UART: 1/3 channel
• Simplified I2C: 0/2/3 channel

Product Overview

The Renesas Starter Kit for RL78 is intended as a user-friendly introductory and evaluation tool for the RL78/G12 - microcontroller. The board also provides a useful platform for evaluating the Renesas suite of development tools for coding and Flashing , using High-performance Embedded Workshop as well as programming the device using Flash Development Toolkit.

The Renesas Starter Kit for may be connected to the host PC using a simple RS232 serial connection (not normally fitted) or via the included USB interface CP2102 USB to uart converter Chip Included on the Board.

The purpose of the board is to enable the user to evaluate the capabilities of the device and its peripherals by giving the user a simple platform on which code can be run only minutes from opening box. It can also prove an invaluable tool in development by providing a useful test platform for code already debugged using one of our more powerful emulation tools.

NSK Starter Kit Features
MAIN Features

• USB Powered
• RS232 Tx, Rx interface with MAX232 IC on socket
• Quartz crystal 20.000Mhz
• Reset button
• Power plug-in jack
• Extension slot on every uC pin
• GND bus
• Vcc bus
• Four mounting holes 3,3 mm (0,13")

Package Content

• Renesas Development Board ( WITH CHIPS RS232,RTC1307,24c02 ,LCD 16X2).
• USB cable.
• Software CD( Renesas IDE,Flash Tool kit,Datasheets).

Additional Information:

• Item Code: SEES-1121
• Production Capacity: 1000 NOS
• Delivery Time: 1-2 Days
• Packaging Details: Carton Boxes

With this board you can develop and prototype with any of 8051 40 pin microcontrollers. The RS232 driver on board allows easy connection with PC or other embedded hardware ( Easy to falsh 89v51Rd2 Through flash magic, SST through SST Flasher, Nuvoton through Nuvoton Flasher). The board have User buttons and status LEDs. The bridge rectifire allow this board to be powered with both AC and DC power supply adapters.

Features:

• RS232 Tx, Rx interface with MAX232 IC on socket
• DIL40 ZIF Socket ( Zero Insertion Force) microcontroller socket.
• Reduce Microcontroller Damages
• Reset button.
• Power plug-in jack(power supply AC/DC 12V).
• Extension slot on every uC pin with pull up resistor for port0 and port1.
• GND bus.
• Vcc bus.

 

I/O Features:

• Easy to test with Burg Connecters wires.
• A Serial Port for ISP.
• 7Seg Mulitplexed Display.
• Ready Interface for LCD display 2x16
• 24Cxx I2C EEPROM.
• RTC DS1307.
• 8 LED array.
• 4 Interupt Switches.
• ULN2003 To Drive Stepper Motor and Relays.
• Eaxample Programs for LED,7seg,LCD,RS232 ,Matrix Key Pad, ADC.
• Easy To flash 89V51RD2 Through Flash Magic Software.

 

Package Content:

• 8051 Development Board ( WITH CHIPS RS232, RTC1307,I2C24004,ULN2003).
• Burg Connecters 20 Nos.
• Software CD( Flash Magic, Data sheets, Example Porograms, Manual, Keil Eva).

Additional Information:

• Item Code: SEES-1053
• Production Capacity: 1000 NOS
• Delivery Time: 1-2 DAYS
• Packaging Details: Carton Boxes

LPC2129 Chip Features:

• 16/32-bit ARM7TDMI-S microcontroller.
• 16 kB on-chip RAM
• In-System Programming (ISP) and In-Application Programming (IAP) via on-chip boot-loader software.
• On-chip Embedded-ICE-RT, Embedded Trace Macrocell debugger.
• Two interconnected CAN interfaces with advanced acceptance filters.
• Four channel 10-bit A/D converter with conversion time as low as 2.44 ms.
• Multiple serial interfaces including two UARTs (16C550).
• Fast I2C (400 kbits/s) and two SPIs.
• Phase-Locked Loop with settling time of 100 ms.
• Vectored Interrupt Controller with configurable priorities and vector addresses.
• Two 32-bit timers (with four capture and four compare channels), PWM unit (six outputs).
• Real Time lock and Watchdog.
• Up to forty-six 5V tolerant general purpose I/O pins.
• Up to nine edge or level sensitive external interrupt pins available.
• On-chip crystal oscillator 
• Two low power modes: Idle and Power-down.
• Processor wake-up from Power-down mode via external interrupt.
• Individual enable/disable of peripheral functions for power optimization.

 

Package Content:

• MINI ARM 7 Development Board.
  Rs232 Port Cable for ISP Programming.
• Software CD( Phuilips Downloader, Data sheets,Example Porograms, Manual, Keil3 Evalution MAX 16 kb.

 

Additional Information:

• Item Code: SEES-1095
• Production Capacity: 1000 NOS
• Delivery Time: 1-2 DAYS
• Packaging Details: Carton Boxes

What is Launch Pad LaunchPad is an easy-to-use development tool intended for beginners and experienced users alike for creating microcontroller-based applications. the LaunchPad offers everything you need to get started with your projects.

Additional Information:

• Item Code: SEES-1117
• Production Capacity: 1000 NOS
• Delivery Time: 1-2 DAYS
• Packaging Details: CARTON BOXES

A general purpose 40 pin avr development board with on board power supply circuit, RS232 port for serial interface with computer and other serial devices, reset switch, power status LED and a general purpose switch and LED.The bridge rectifier allows this board to be powered with both AC and DC power supply adapters. 

 

Features:

• AVR Development Board for 40 pin Atmel AVR series.
• ISP Socket for Flashing thru AVR Dude and AVR Prog.
• On board Regulated Power Supply 5v, 12v supply’s.
• Easy to test with Burg Connectors wires.
• An RS232 Serial Port.
• 7Seg Multiplexed Display.
• Ready Interface for LCD display 2linex16Character.
• 24Cxx I2C EEPROM.
• RTC DS1307.
• 4 LED array.
• 4x4 Matrix Key Pad.
• 4 Interrupt Switchers.
• Extension slot on every uC pin.
• ULN2003 To Drive Motor and Relays.
• Example Programs for LED, 7seg, LCD, RS232, Matrix.
• 1 Channel Relay For testing.

 

Package Content:

• AVR Development Board (WITH CHIPS RS232, RTC1307, I2C24004, ULN2003).
• Burg Connectors 20 No’s.
• Software CD( Data sheets, Example Programs, Manual).

Additional Information:

• Item Code: SEES-1088
• Production Capacity: 1000 NOS
• Delivery Time: 1-2 DAYS
• Packaging Details: Carton Boxes

 

PIC STARTER KIT 18F4520 BASED  

Introduction :

       PIC starter Kit is based on Pic 18f4520 Based  , Bootloader Based , No need Of programmers , Thru Rs232  port Easiliy Hex file can Be downloaded  using  Flash Utility.

Features :

•    DIL40 microcontroller socket with PIC IC.
•    RS232 Tx, Rx interface with MAX232 IC on socket.
•    ULN 2003 To Drive Stepper Motor & Relays.
•    Quartz crystal 20Mhz.
•    On board lcd display.
•    2 LED.
•    2 Push Button.
•    RTC DS1307.
•    Reset button.
•    Power plug-in jack(power supply AC/DC 12V).
•    Extension slot on every uC pin.
•    GND bus.
•    VCC bus.
•    Four mounting holes 3,3 mm (0,13").

 

Additional Information:

• Item Code: SEES-1067
• Production Capacity: 1000 NOS
• Delivery Time: 1-2 DAYS
• Packaging Details: Carton Boxes

QUICK OVERVIEW

1. Chipboard STM32F103C8T6
2. On board, SWIM interface and reset button
3. Micro USB line or the 2.54 pin to link to the power with the input voltage 4.5V-15V.
4. Power light and the Demo indicator light
5. Leads all the pins and has detailed label for the Pins.
6. Support SWIM debug mode.

The advantages of the Core Board STM8S103F3P6 STM8 Development Board Minimum System Board is this development board uses the Micro USB to link to the power. The Micro USB line is compatible with Smartphone cable which means we can get the data easily.  We do not use the USB MINI cable to link to power because the USB MINI cable has out of style and very difficult to get.

This STM8S development board draws our attention because of its low price, humanity design and available with complete information.

You can use 2.54 pin on the board or power supply pad, the pad when using the power supply, input voltage range 4.5V-15V can output to the outside through pin 3.3V!

This development board using MicroUSB cable supply, compatible with smartphone lines, data lines are simple and easy to get, but not USB MINI line-powered, USB MINI line is not easy to find, has been gradually phased out. Other manufacturers of products are used in MINI-USB port, this is not applicable for customers.
Low price, user-friendly design, a full set of data, allowing you to save money, save time, effort, worry!

Note!! 5V pin’s voltage is the input voltage of the module.Performance comparison:

EEPROM: The STM8S003F3 has 128 bytes, while the STM8S103F3 has 640 bytes.
Flash Erase: STM8S003F3 100 times, while the STM8S103F3 has 10000 times.
Flash: The STM8S103F2 only has 4K bytes, while the STM8S103F3 has 8K bytes.
Conclusion: STM8S003F3 is only suitable for mature products, while the STM8S103F3 can be used to develop new function according to our request.

Features :

1. Chipboard STM32F103C8T6
2. On board, SWIM interface and reset button
3. Micro USB line or the 2.54 pin to link to the power with the input voltage 4.5V-15V.
4. Power light and the Demo indicator light
5. Leads all the pins and has detailed label for the Pins.
6. Support SWIM debug mode.

Package Includes :

1 x Core Board STM8S103F3P6 STM8 Development Board

Additional Information:

• Item Code: SEES-3133
• Production Capacity: 1000 NOS
• Delivery Time: 1-2 DAYS
• Packaging Details: CARTON BOXES

With this board you can develop and prototype with any of Microchip's 40 pin PIC microcontrollers. The RS232 driver on board allows easy connection with PC or other embedded hardware. The board has User button and status LED. The bridge rectifier allows this board to be powered with both AC and DC power supply adapters.

Features:

• RS232 Tx, Rx interface with MAX232 IC on socket.
• DIL40 microcontroller socket.
• Reset button
• Extension slot on every uC pin.
• 1 output LED 
• ICSP programming Connector.
• GND bus.
• VCC bus.

Additional Information:

• Item Code: SEES-1074
• Production Capacity: 1000 NOS
• Delivery Time: 1-2 DAYS
• Packaging Details: Carton Boxes

QUICK OVERVIEW

1. 100% Brand new and high quality STM32 Board
2. Model: STM32F103C8T6.
3. Core: ARM 32 Cortex-M3 CPU.
4. Debug mode: SWD.
5. 72MHz work frequency.
6. 64K flash memory, 20K SRAM.
7. 2.0-3.6V power, I/O.

This is STM32F103C8T6 Minimum System Board Microcomputer STM32 ARM Core Board. This board is a low-cost Minimum System Development Board for ARM Microcontroller STM32F103C8T6.

Board is suitable for learners that want to learn STM32 microcontroller with ARM Cortex-M3 32-bit core.

Features :

1. 100% Brand new and high-quality STM32 Board
2. 72MHz work frequency.
3. 64K flash memory, 20K SRAM.
4. 2.0-3.6V power, I/O.
5. Reset(POR/PDR).
6. 4-16MHz crystal.
7. Onboard Mini USB interface, you can give the board power supply and USB communication.

Package Includes :

1 x STM32F103C8T6 Minimum System Board Microcomputer STM32 ARM Core Board

Additional Information:

• Item Code: SEES-3132
• Production Capacity: 1000 NOS
• Delivery Time: 1-2 DAYS
• Packaging Details: CARTON BOXES

With this board you can develop and prototype with any of Microchip's 40 pin PIC microcontrollers. The RS232 driver on board allows easy connection with PC or other embedded hardware, The board have User buttons and status LEDs. The bridge rectifire allow this board to be powered with both AC and DC power supply adapters.

Features:

• PIC Development Board for Microchip PIC Series  For any 40 Pin series  16FXXX , 18FXXX    (EX 16F877A - 40 pin).
• ICSP Socket for Programming through PICKIT2
• During Testing Easy to Remove Chips with ZIP Socket.
• Easy to test with Burg Connecters wires.
• An RS232 Serial Port.
• 7Seg Multiplexed Display.
• LCD display 2linex 16 Character.
• 24Cxx I2C EEPROM.
• RTC DS1307.
• 4 LED array.
• 4 Interrupt Switchers.
• ULN2003 To Drive Relays and Stepper Motors.
• Two 1K pot for analog input
• Example Programs for LED,7seg,LCD,RS232 ,Matrix Key Pad, ADC. Package Contents :
• PIC Development Board.
• Includes RS232 IC, ULN 2003 IC, RTC1307 IC, I2C 24C04 IC.
• Burg Connecters 20 No’s.
• Software CD (Data sheets, Example Programs, Manual, Schematic).

Additional Information:

• Item Code: SEES-1065
• Production Capacity: 1000 NOS
• Delivery Time: 1-2 DAYS
• Packaging Details: Carton Boxes

PIC Development Board With this board you can develop and prototype with any of
Microchip's 40 pin PIC microcontrollers. this  Board is used to evaluate and demonstrate the capabilities of Microchip PIC16F877A microcontroller. The board is designed for general purpose applications and includes a variety of hardware to exercise microcontroller peripherals. It is a fantastic tool for code debugging, development and prototyping. The all new board design have made it much more user-friendly than its predecessors, ideally suitable for training and development purposes. The RS232 driver on board allows easy connection with PC or other embedded hardware, The board have User buttons and status LEDs. The bridge rectifire allow this board to be powered with both AC and DC power supply adapters.

Features:

• PIC Development Board for Microchip PIC Series  For any 40 Pin series  16FXXX , 18FXXX    (EX 16F877A - 40 pin).
• ICSP Socket for Programming through PICKIT2
• Easy to test with Burg Connecters wires.

Additional Information:

• Item Code: SEES-1066
• Production Capacity: 1000 NOS
• Delivery Time: 1-2 DAYS
• Packaging Details: Carton Boxes

LPC 2148 Development Board-LPC214X is an evaluation board for LPC2148 ARM7TMDI based microcontroller. The LPC2148 microcontroller has 512KB of internal flash and 32+8K RAM. Following are the salient features of the board.

Features:

• JTAG connector.
• SD/MMC connector.
• USB B-type connector with Link-LED.
• All peripheral configurable via jumpers.
• I2C based EEPROM.
• Line 2X16 character LCD with back light control.
• Ready to Interface 128X64 GRAPHICAL DISPLAY – Optional.
• Two 1k pots for analog input.

 

Package Content :

• 2148 Board.
• Serial cable.
• Software CD.

Additional Information:

• Item Code: SEES-1096
• Production Capacity: 1000 NOS
• Delivery Time: 1-2 DAYS
• Packaging Details: Carton Boxes