Sri Electronics & Embedded Solutions

QUICK OVERVIEW

1. Working voltage: 3 ~ 5V
2. Board size:54 x 38 mm
3. ISD1820 Sound/Voice Board Recording
4. 100% Brand new and high-quality Board
5. ISD1820 chip with an Onboard microphone

This is ISD1820 Sound/Voice Board Recording Module. The ISD1820 Sound/Voice Board Recording is 100% Brand new and high-quality Board ISD1820 chip with an Onboard microphone, you can direct recording of About 10 seconds voice recording. High-quality, natural voice Restore can be used as a loudspeaker module With a loop playback, jog playback, single-pass playback.

The chip pin leads, through the microcontroller to control operation.

This voice record/playback device is based on the ISD1820 chip, which can record/playback multiple-message. It can offer true single-chip voice recording, non-volatile storage, and playback capability for 8 to 20 seconds. For the sampling rate of 3.2KHz, it can record for the total duration of 20 seconds.

Features :

1. Working voltage: 3 ~ 5V
2. Board size:54 x 38 mm
3. ISD1820 Sound/Voice Board Recording
4. 100% Brand new and high-quality Board
5. ISD1820 chip with an Onboard microphone.

Package Includes :

1 x ISD1820 Sound/Voice Board Recording Module

Additional Information:

• Item Code: SEES-3364
• Production Capacity: 1000 NOS
• Delivery Time: 1-2 DAYS
• Packaging Details: CARTON BOXES

QUICK OVERVIEW

1. Driver Chip: MAX7219
2. Input Voltage: 3.7 to 5.3 V
3. Input Current: 320 mA
4. Display Dimensions: 32x32x6 (LxWxH) mm
5. PCD Dimensions: 50×32 (LxW) mm

Additional Information:

• Item Code: SEES-3410
• Production Capacity: 1000 NOS
• Delivery Time: 1-2 DAYS
• Packaging Details: CARTON BOXES

Description

A RS232 to RS485 Communication Converter Adapter.RS232 Communication Converter is widely used in industrial automation, door safe, all-in-one-card, car parking, ATM, bus charge, eatery sell out, staff attendance management, and highway toll gate, etc. This
RS485 Communication Converter is capable of applying between host computers, host computer and its external equipments and forms point to point, point to multi-points network.

•  Compatible with EIA/TIA RS-232C, RS485 standard.
• Interface RS232 side: DB9 female connector.
•  Interface RS485 side: DB9 male connector with terminal board.
• Working mode: asynchronous, half-duplex, differential transmission.
• Transmission media: double wire or Shielding double Line.
• Transmission rate: 300 – 115200bps

Additional Information:

• Item Code: SEES-3575
• Production Capacity: 1000 NOS
• Delivery Time: 1-2 DAYS
• Packaging Details: CARTON BOXES

QUICK OVERVIEW

1. Supply Voltage: 4.5 – 5.5 V.
2. Current : <40 mA.
3. Digital Interface : 5V TTL level for UART interface and GPIO.
4. Support maximum 80 voice commands, with each voice 1500ms (one or two words speaking).
5. Maximum 7 voice commands effective at same time.
6. Arduino library is supplied.
7. User-control General Pin Output.

Speak (Voice) Recognition Module V3 compatible with Arduino is a compact and easy-control speaking recognition board.

Speak (Voice) Recognition Module V3 product is a speaker-dependent voice recognition module. It supports up to 80 voice commands in all. Max 7 voice commands could work at the same time. Any sound could be trained as the command. Users need to train the module first before let it recognizing any voice command.

This board has 2 controlling ways: Serial Port (full function), General Input Pins (part of a function). General Output Pins on the board could generate several kinds of waves while the corresponding voice command was recognized.

What are the updated features?

We have Voice Recognition module V2 and it supports 15 commands in all and only 5 commands at the same time. On V2, voice commands are separated into 3 groups while you training it. And only one group (5 commands) could be imported into Recognizer. It means only 5 voice commands are effective at the same time.

On V3, voice commands are stored in one large group like a library. Any 7 voice commands in the library could be imported into recognizer. It means 7 commands are effective at the same time. 

Features :

1. Support a maximum of 80 voice commands, with each voice 1500ms (one or two words speaking).
2. Maximum 7 voice commands effectively at the same time.
3. Arduino library is supplied.
4. User-control General Pin Output.
5. Analog Interface: 3.5 mm mono-channel microphone connector +  microphone pin interface.

Package Includes :

1 x Voice Recognition Module V3.

1 x Microphone.

4 x F-F Jumper Wires. (10 cm)

1 x Set of Berg Pins(Right Angle)

Additional Information:

• Item Code: SEES-3701
• Production Capacity: 1000 NOS
• Delivery Time: 1-2 DAYS
• Packaging Details: Carton Boxes

QUICK OVERVIEW

1. Model number: TEC1-12705
2. Operating Voltage: 12V
3. Maximum Voltage- Umax (V) : 15V
4. Maximum Current- Imax (A) : 5.2A
5. Maximum Power : 54 W
6. Power Cord: 25cm

The TEC1-12705 40x40mm Thermoelectric Cooler 5A Peltier Module is the simple application of Peltier Thermoelectric Effect. The module features 127 semiconductor couples in the area of 40mmx40mm which very effectively cools and heats up to 80°C.

Thermoelectric coolers also are known as TEC or Peltier Module create a temperature differential on each side. One side gets hot and the other side gets cool. Therefore, they can be used to either warm something up or cool something down, depending on which side you use. You can also take advantage of a temperature differential to generate electricity.

This Peltier works very well as long as you remove the heat from the hot side. After turning on the device, the hot side will heat quickly, the cold side will cool quickly. If you do not remove the heat from the hot side (with a heat sink or other device), the Peltier will quickly reach stasis and do nothing. We recommend using an old computer CPU heatsink or another block of metal to pull heat from the hot side. We were able to use a computer power supply and CPU heatsink to make the cold side so uncomfortable we could not hold our finger to it.

A thermoelectric cooling (TEC) module is a semiconductor-based electronic component that functions as a small heat pump. By applying the DC power source to a TEC, heat will be transferred from one side of the module to the other. It creates a cold and hot side. They are widely used in industrial areas, for example, computer CPU, CCDs, portable refrigerators, medical instruments, and so on.

Also Known as Thermoelectric cooling modules, Thermoelectric modules, Peltier modules, Thermoelectric cooling module.

Operating Tips:

1. Do not exceed Imax or Vmax when operating a module.
2. Please carry out moisture protection options (sealing) in final application use.
3. Life expectancy: 200,000 hours
4. Failure rate based on longtime testings: 0.2%.

Important Note!! Heat side requires heat sink all the time. “ Do not run this device with a power supply more than a few seconds without a heatsink mounted to the device! ”

Features :

1. Small module.
2. Easy transition between the hot side to the cool side and vice-versa just by reversing the polarity of the supply.
3. Quality tested cooling cells.
4. Solid-state, vibration free, noise-free.
5. Simple to install and operate.
6. Should use with a heat sink.

Package Includes:

1 x TEC1-12705 40x40mm Thermoelectric Cooler 5A Peltier Module

Additional Information:

• Item Code: SEES-3649
• Production Capacity: 1000 NOS
• Delivery Time: 1-2 DAYS
• Packaging Details: CARTON BOXES

If you want to add some visual output to your Arduino projects, you’ll need a display. If you need only little to display, the LCD1602 Parallel LCD Display with IIC/I2C interface is a quite good solution.

This is LCD1602 Parallel LCD Display that provides a simple and cost-effective solution for adding a 16×2 White on RGB Liquid Crystal Display into your project. The display is 16 character by 2 line display has a very clear and high contrast white text upon a blue background/backlight.

This is great blue backlight LCD display. It is fantastic for Arduino based project. This LCD1602 Parallel LCD Display with Yellow Backlight is very easy to interface with Arduino or Other Microcontrollers.

This display overcomes the drawback of LCD1602 Parallel LCD Display in which you’ll waste about 8 Pins on your Arduino for the display to get working. Luckily in this product, an I2C adapter is directly soldered right onto the pins of the display. So all you need to connect are the I2C pins, which shows a good library and little of coding.

The I2C is a type of serial bus developed by Philips, which uses two bidirectional lines, called SDA (Serial Data Line) and SCL (Serial Clock Line). Both must be connected via pulled-up resistors. The usage voltages are standard as 5V and 3.3V.

If you already have the I2C adapter soldered onto the board like in this product, the wiring is quite easy. You should usually have only four pins to hook up. VCC and GND of course. The LCD display works with 5 Volts. So we go for the 5V Pin.

The values shown on the display can be either a simple text or numerical values read by the sensors, such as temperature or pressure, or even the number of cycles that the Arduino is performing.

If you are having an I2C adapter and only want to buy display then click below,

LCD1602 Parallel LCD Display

For more displays click below,

LED/LCD Display

Features :

1. Arduino IIC/I2C interface was developed to reduce the IO port usage on Arduino board
2. I2C adapter allows flexibility in connections
3. I2C Reduces the overall wirings.
4. 16 characters wide, 2 rows
5. White text on the Blue background
6. Single LED backlight included can be dimmed easily with a resistor or PWM.

QUICK OVERVIEW

1. Model: LCD1602
2. Interface: I2C
3. Interface Address: 0x27
4. Character Color: White
5. Backlight: Blue
6. Supply voltage: 5V
7. Dimensions: 80 x 36 x 18 (LxWxH) mm.

  Package Includes :

1 x LCD1602 Parallel LCD Display with IIC/I2C interface

5V 1,2,4& 8 Channel SSR G3MB-202P Solid State Relay Module 240V 2A Output with Resistive Fuse

A 1,2,4& 8 channel relay module (HCMODU0115) featuring 2x Omron G3MB-202P solid state relays. This 5V 1,2,4& 8 channel  SSR G3MB-202P Solid State Relay Module is capable of switching AC voltages between 100 and 240V at up to a 2A current. The module can be controlled from a 5V digital source such as an Arduino microcontroller.

A resistive type fuse is provided on the module to help protect excessive current draw.

This 5V 1,2,4& 8 channel SSR G3MB-202P Solid State Relay Module 240V 2A Output with Resistive Fuse is based on the Omron G3MB SSR relay which can control up to 2A at 240VAC. This is a 2 Channel SSR relay module, each relay channel has 3 separate terminals, NO (Normal Open), COM (Common), NC (Normal Closed).

A Solid State Relay is similar to a mechanic relay where it can be controlled through a digital signal. Solid State Relay generates no noise and has a much longer lifespan in compared to the traditional mechanic relay.

When the input logic voltage is applied to the coil, the NC will disconnect from the COM breaking the conductivity between the two. At the same time, the NO will connect with the COM allowing conductivity between them. Depending on your wiring this will turn on or off the connected load.

Input part :

1. DC+: connect the power supply positive (press the relay voltage power supply)
2. DC-: the cathode of a power supply
3. CH1: 1 relay module signal trigger end (high-level trigger effective)
4. CH2: 2 relay module signal trigger end (high-level trigger effective)

High level and low level of meaning

1. High-level trigger refers to the signal trigger end (IN) had a positive voltage and the negative pole of the power supply is usually between, and the triggering end of a trigger connected with the positive pole of a power supply, when the trigger end has a positive voltage or reached the trigger voltage, the relay is attracted.
2. Low-level trigger refers to the signal triggering voltage between the end and the negative electrode of the power supply is OV, or trigger terminal voltage lower voltage than the positive power supply voltage, low to can trigger, make the relay, is usually the cathode of the power supply and the triggering end of a trigger mode connection, so that the relay is attracted.

Features :

1. 1,2,4& 8 channel 2 AMP Solid State Relay board
2. Control 1,2,4 & 8  loads of up to 2 amps each at 120V or 240V AC.
3. Good for lighting, holiday displays etc.
4. Has been assembled, and the electrical test passed.
5. Led indicator for each relay.
6. Use it to control various appliances and other equipment with a large current.
7. It can be controlled directly by Microcontroller
8. The 2.54CM pin and blue KF301 terminal are connected to the line of control.
9. Input control signal voltage:
   1. 0-0.5V the state of low-level relay OFF
   2. 0.5-3.3V Unknown State
   3. 3.3-5V high-level relay ON

Additional Information:

• Item Code: SEES-3020
• Production Capacity: 1000 NOS
• Delivery Time: 1-2 DAYS
• Packaging Details: CARTOON BOXES

QUICK OVERVIEW

1. Storage capacity: 3000 fingerprints.
2. Finger window: 12.9 x 16.9 mm.
3. Image Size: 258 x 202 Pixels.
4. Resolution: 450 dpi.
5. CPU: ARM Cortex M3 Core MCU).

The GT521F52 Optical Fingerprint Scanner Module with JST SH Connector is a high-performance fingerprint scanner. Which is useful for to access control, security, identification, and convenience. This optical sensor module is designed for easy integration into applications with serial interface (UART). We need two wires are for TX and RX and two wires for power supply (5V).

The main difference between GT521F32 and GT521F52 is fingerprint storage capacity.

There are four types of fingerprint scanner: the optical scanner, the capacitance scanner, the ultrasonic scanner, and the thermal scanner. The GT521F52 Fingerprint Scanner Module is an optical scanner module. This optical scanner takes a visual image using a digital camera.

The idle module is woken by a finger touching the metal frame of the sensor. The pictures of the fingerprints are processed on-board by the fingerprint algorithm (low power 32-bit ARM Cortex-M3 processor) and convert it into strings of data. These so-called ‘templates’ are residing on the module configured as a USB mass storage device. They can store and share through a database with other modules in a network, allowing easy enrollment of many users.

Features :

1. Ultra-thin Optical Sensor.
2. High-accuracy & high-speed fingerprint identification technology.
3. Works well with dry, moist or rough fingerprints.
4. 3000 fingerprints storage.
5. Wake up on Finger Function.
6. Easy one-touch enrollment.
7. 1: 1 verification, 1: N identification.
8. Simple UART & USB communication protocol.
   external UART-to-USB converter required (TX & RX levels: 3.3V).
9. Complies with USB 2.0 full-speed (12 Mbps) specifications.
10. Reading & writing fingerprint template(s) (i.e. processed data) from/to the device.
11. Downloading the raw bitmap image from the device (catalog fingerprints).
12. Anti-Scratch with surface high hardness ??? 5H.

Package Includes:

1 x GT521F52 Optical Fingerprint Scanner Module.

2 x 1 mm pitch 4 pin JST SH Connector.

Additional Information:

• Item Code: SEES-3284
• Production Capacity: 1000 NOS
• Delivery Time: 1-2 DAYS
• Packaging Details: CARTON BOXES

QUICK OVERVIEW

1. Dimensions: 40 x 27 x 15 (LxWxH) mm.
2. Weight: 10gm (without Hat).
3. 2.54mm pin interface leads.
4. Operating Voltage: 5V.
5. Long service life and stable performance.
6. Standard interface and electronic building blocks.
7. Widely use in Arduino DIY projects.

This is JoyStick Module PS2 Breakout Sensor very similar to the ‘analog’ joysticks on PS2 (PlayStation 2) controllers. Directional movements are simply two potentiometers – one for each axis. Pots are ~10k each. This joystick also has a select button that is actuated when the joystick is press down.

With the help of this Joystick Module, you can measure position coordinates on the X and Y axis by moving the “hat”. It also contains a switch that is press-able by pushing the “hat”.It also contains a switch that is press-able by pushing the “hat” down. Similar to the XBOX controller.

The X and Y axes are two 10k potentiometers which control 2D movement by generating analog signals. When the module is in working mode, it will output two analog values, representing two directions. This module uses the 5V power supply, and value, when reading through analog input, would be about 2.5V, a value will increase with joystick movement and will go up till maximum 5V; the value will decrease when the joystick is moved in other direction till 0V.

 

Applications:

1.As square wave signal generator which generates a square wave signal

2. To provide a signal to the stepping motor driver

3. Adjustable pulse generation for chip use

4. Produce variable pulse signal, the control-related circuit (PWM dimming, speed)

Module Description:

Frequency is divided into three ranges:

1.XXX (no decimal point):the smallest unit is 1Hz,the range 1Hz-999Hz

2.XX.X (decimal point in ten): The minimum unit is 0.1Khz; the range of 0.1KHz-99.9KHz

3.X.X.X.(there is three decimal point): the smallest unit is 1Khz; the range 1KHz-150KHz

Frequency Display Example:

1.”100″ indicates that the PWM output pulse of 100Hz

2.”54.1″ indicates that the PWM output pulse of 54.1KHz

3.”1.2.4.” Indicates that the PWM pulse output 124KHz

4.Duty Cycle in the range:0 to 100

5. Three frequencies duty cycle is the same, all the parameters non-volatile

Features:

1. 2.54mm pin interface leads
2. Long service life and stable performance
3. Standard interface and electronic building blocks
4. Widely use in Arduino DIY projects
5. Cross rocker as a two-way 10K resistor, with the rocker in a different direction.

Additional Information:

• Item Code: SEES-3368
• Production Capacity: 1000 NOS
• Delivery Time: 1-2 DAYS
• Packaging Details: CARTON BOXES

QUICK OVERVIEW

1. Ultra-thin design & adhesive backing provides easy integration to any project
2. Excellent price-performance ratio
3. Easy communication with any microcontroller
4. 5 pins 2.54mm pitch connector, 4x 4type 16 keys.
5. Sticker can peel off for adhesive mounting.
6. Operating Voltage (V): 12 DC

This DC 12V 4×3 Matrix 12 keys Membrane Switch Keypad is high-quality soft touch feeling button keypad with 100 million life-stroke lifespans and good resistance to environmental conditions.

This DC 12V 4×3 Key Matrix Membrane Switch Keypad is a high-quality product at very low cost for your application needs.

This 12-button keypad provides a useful human interface component for microcontroller projects. Convenient adhesive backing provides a simple way to mount the keypad in a variety of applications.

The Keypad 4×3 features a total of 12 buttons in Matrix form. This is a membrane keypad with no moving parts. A female 7-pin berg connector is require for interfacing it with your microcontroller circuits.

Features :

1. Ultra-thin design & adhesive backing provides easy integration to any project
2. Excellent price-performance ratio
3. Easy communication with any microcontroller
4. 5 pins 2.54mm pitch connector, 4×3 type 12 keys.
5. Sticker can peel off for adhesive mounting.
6. Used widely in industrial and home electronic equipments, instrument, etc.
7. This allows a microcontroller to ‘scan’ the 7 output pins to see which of the 12 buttons is being pressed.

Additional Information:

• Item Code: SEES-3375
• Production Capacity: 1000 NOS
• Delivery Time: 1-2 DAYS
• Packaging Details: CARTON BOXES

QUICK OVERVIEW

1. Operating voltage: 2.5V-5.5V
2. Maximum output power: 3W x 2
3. PCB size is about: length 30mm width 22mm overall height after installed is about 16mm
4. Built with switch Potentiometer, can adjust the volume & control power switch freely!
5. Flexible assembly usage.

This is PAM8403 Mini 5V Digital Amplifier Board With Switch Potentiometer. PAM8403 is a small digital amplifier chip, high-definition sound quality highlights the advantages of digital chips, the circuit using the most reasonable peripheral configuration, power supply filtering is upgraded to 470uf (some sellers are less did not even 100uf capacitance).

1.6mm glass sheet, the real amplifier board did the most detailed, high-fidelity sound output 3W + 3W, is a rare good product enthusiasts amplifier, potentiometer using the original anti-meter body, potentiometer with the switch can cut off the power supply directly counterclockwise.

Usage:
Suitable for battery or portable electronics products, suitable for long time steady usage.

Note!!!
Please make sure the power supply is not more than 5.5V and please don’t do reverse polarity for “+” and “-“, or else, it will burn the board. 

Features :

1. PCB size is about: length 30mm width 22mm overall height after installed is about 16mm
2. Built with switch Potentiometer, can adjust the volume & control power switch freely!
3. Flexible assembly usage.

Package Includes :

1 x PAM8403 Mini 5V Digital Amplifier Board

Additional Information:

• Item Code: SEES-3500
• Production Capacity: 1000 NOS
• Delivery Time: 1-2 DAYS
• Packaging Details: CARTON BOXES

QUICK OVERVIEW

1. 5V power supply.
2. Serial I2C control of LCD display using PCF8574.
3. Backlight can be enabled or disabled via a jumper on the board.
4. Contrast control via a potentiometer.
5. Can have 8 modules on a single I2C bus (change address via solder jumpers)address, allowing.

This is a RoHS compliant I2C Serial LCD Daughter board that can be connected to a standard 16×2 or 20×4 Character Display Module that supports 4-bit mode. All Character Modules sold on our site support 4-bit mode, and nearly all commercially available 16×2 and 20×4 line character modules support it too.

This board has a PCF8574 I2C chip that converts I2C serial data to parallel data for the LCD display. There are many examples on the internet for using this board with Arduino. Do a search for “Arduino LCD PCF8574“. The I2C address is 0x3F by default, but this can be changed via 3 solder jumpers provided on the board. This allows up to 3 LCD displays to be controlled via a single I2C bus (giving each one it’s own address)

Specifications and Features:

1. 5V power supply.
2. Serial I2C control of LCD display using PCF8574.
3. Backlight can be enabled or disabled via a jumper on the board.
4. Contrast control via a potentiometer.
5. Can have 8 modules on a single I2C bus (change address via solder jumpers)address, allowing.
6. Size ???41.6 x 19.2 mm.

Package Includes:

1 x IIC/I2C Serial Interface Adapter Module

Additional Information:

• Item Code: SEES-3351
• Production Capacity: 1000 NOS
• Delivery Time: 1-2 DAYS
• Packaging Details: Carton Boxes

QUICK OVERVIEW

1. Voltage version: 5V
2. The static current: 5mA
3. Working current: 190mA
4. Trigger current: 2-4mA
5. Optical coupling isolation, driving ability is strong, stable performance; Trigger current is 5mA
6. The module can be set high level or low-level trigger by the jumper
7. Rated current of the interface is 16A

Additional Information:

• Item Code: SEES-1565
• Production Capacity: 1000 NOS
• Delivery Time: 1-2 DAYS
• Packaging Details: Carton Boxes

QUICK OVERVIEW

1. Finger window: 12.9 x 16.9 mm.
2. Image Size: 258 x 202 Pixels.
3. Storage capacity: 200 fingerprints.
4. Wake up on Finger Function.
5. Anti-Scratch with surface high hardness ??? 5H.
6. Resolution: 450 dpi.
7. CPU: ARM Cortex M3 Core MCU).

The GT521F32 Optical Fingerprint Scanner Module with JST SH Connector is a high-performance fingerprint scanner. Which is useful for to access control, security, identification, and convenience. This optical sensor module is designed for easy integration into applications with serial interface (UART). We need two wires are for TX and RX and two wires for power supply (5V).

The main difference between GT521F32 and GT521F52 is fingerprint storage capacity.

The Difference between GT511C3 and GT521F32 is :

 

There are four types of fingerprint scanner: the optical scanner, the capacitance scanner, the ultrasonic scanner, and the thermal scanner. The GT521F32 Fingerprint Scanner Module is an optical scanner module. This optical scanner takes a visual image using a digital camera.

The idle module is woken by a finger touching the metal frame of the sensor. The pictures of the fingerprints are processed on-board by the fingerprint algorithm (low power 32-bit ARM Cortex-M3 processor) and convert it into strings of data. These so-called ‘templates’ are residing on the module configured as a USB mass storage device. They can store and share through a database with other modules in a network, allowing easy enrollment of many users.

Features :

1. Ultra-thin Optical Sensor.
2. High-accuracy & high-speed fingerprint identification technology.
3. Works well with dry, moist or rough fingerprints.
4. 200 fingerprints storage.
5. Wake up on Finger Function.
6. Easy one-touch enrollment.
7. 1: 1 verification, 1: N identification.
8. Simple UART & USB communication protocol.
   external UART-to-USB converter required (TX & RX levels: 3.3V).
9. Complies with USB 2.0 full-speed (12 Mbps) specifications.
10. Reading & writing fingerprint template(s) (i.e. processed data) from/to the device.
11. Downloading the raw bitmap image from the device (catalog fingerprints).
12. Anti-Scratch with surface high hardness ??? 5H

Additional Information:

• Item Code: SEES-3283
• Production Capacity: 1000 NOS
• Delivery Time: 1-2 DAYS
• Packaging Details: CARTON BOXES

MP3-TF-16P MP3 Disk TF Card Module Serial Port is a compact and inexpensive MP3 module that can be connected directly to the speaker. Module with battery power supply, speaker, the keypad can be used alone, or through the serial port control, as the Arduino UNO or any microcontroller with a serial port module. The module itself perfectly integrated hardware decode MP3, WAV, WMA.

While the software supports TF card driver to support FAT16, FAT32 file system. It can be done by simple serial command plays the specified music, as well as how to play music and other functions, without tedious low-level, easy to use, stable and reliable.

Application

1. Car navigation voice broadcast
2. Road transport inspectors, toll voice prompts
3. The train station, bus station voice prompts security check
4. Electric power, telecommunications, financial operating room voice prompts
5. The vehicle into or out of the channel to verify the voice prompts
6. Border control channel voice prompts
7. Multi-channel voice alarm or voice guidance equipment operation
8. Electric sightseeing bus safety with voice notices
9. Electrical and mechanical equipment failure alarm
10. Fire alarm voice prompts
11. Automatic broadcasting equipment, regular broadcast.

Specifications and Features :

1. Supports sampling rates (kHz): 8 / 11.025 / 12/16 / 22.05 / 24/32 / 44.1 / 48.
2. 24-bit DAC output, dynamic range support: 90dB, SNR support: 85dB.
3. Fully supports FAT16, FAT32 file system, maximum support 32G TF card, support U disk to 32G, 64M bytes of NOR FLASH.
4. A variety of control modes are available. IO control mode, serial mode, AD key control mode.
5. The broadcast language spots feature, you can pause the background music being played. Advertising finished playing back background sound to continue playing.
6. The audio data is sorted by folder, supports up to 100 folders, folders can assign every 255 Tracks
   7,30 level adjustable volume, adjustable EQ 6.

Wiring Diagram :

 

Package Includes:

1 x MP3-TF-16P MP3 Disk TF Card Module Serial Port.

Additional Information:

• Item Code: SEES-3188
• Production Capacity: 1000 NOS
• Delivery Time: 1-2 DAYS
• Packaging Details: Carton Boxes

QUICK OVERVIEW

1. Driver IC: SSD1306
2. Resolution: 128 x 64
3. Visual Angle: >160°
4. Input Voltage: 3.3V ~ 6V
5. Only Need 2 I/O Port Control
6. Pixel Color: Blue

OLED’s are the future of displays, as they possess some of the greatest advantages over both conventional display technologies of LCD’s and LED‘s.

The most attractive thing about using the OLED displays is that they do not need a back-light like conventional LCD/LED screens. The organic material itself has a property known as Electroluminescence (EL), which causes the material to “glow” when stimulated by a current or an electric field. Best energy saving displays ever!!!

This 0.96″ OLED Display Module offers 128×64 pixel resolution. They are featuring much less thickness than LCD displays with good brightness and also produce better and true colors. 

This OLED Display Module is very compact and will add a great ever user interface experience to your Arduino project. The connection of this display with Arduino is made through the I2C(also called as IIC) serial or SPI interface.

The 0.96″ OLED Display Module produces blue text on black background with very good contrast when supplied with DC 2.8V supply. The OLED Display Modules also offers a very wide viewing angle of about greater than 160°.

Setting up SPI/I2C Connection with GMS096A OLED Module :

Being a new entry into the market, only limited resources are available on this small piece of a miracle (GMS096A). I2C/SPI configuration always demands helpful resources as in any case. For the SPI setup, the module comes in 4 wire SPI configuration by default and to make it work with the Arduino you can use these libraries from Adafruit.

For the I2C setup, it demands a little bit of work on the module, let us start with resoldering the resistor from position R3 to R1 and then short the R8 resistor with some soldering tin (0 Ohm resistor). The R6 and R7 pullup resistors are already soldered, nothing to do there. Once done, the module is ready for I2C communication! The CS Pin is not necessarily needed, so just connect it to GND. The DC Pin selects the address. For standard address wire it to GND. The RES-pin needs a low pulse at startup and a high voltage during operation (as in SPI mode), a 100nF capacitor to GND and a 10k resistor to VCC would be ideal!

Features :

1. No need of the backlight
2. The display is self-illuminating
3. Power requirement is low
4. They are offering the large viewing angle
5. Full Compatible with Arduino
6. Factory configured for SPI protocol (can easily change to IIC)
7. Better performance characteristics than traditional LCD and LED displays.
8. Only Need 2 I/O Port Control

Package Includes :

1 x 0.96″ OLED Display Module – SPI/I2C – 128×64 – 7 Pin (Blue)

Additional Information:

• Item Code: SEES-3484
• Production Capacity: 1000 NOS
• Delivery Time: 1-2 Days
• Packaging Details: Carton Boxes

The Digital Sensor TTP223B Capacitive Touch Switch Module is based on a touch-sensing IC (TTP223B) capacitive touch switch module. In the normal state, the module output low, low power consumption; When a finger touches the corresponding position, the module output high, if not touched for 12 seconds, switch to low-power mode. The initial state is low, high touch, do not touch is low ( similar touch of a button feature )Module can be installed in such as surface plastic, glass of non-metallic materials. In addition to the thin paper ( non-metallic ) covering the surface of the module, as long as the correct location of the touch, you can make hidden in the walls, desktops and other parts of buttons.

Touch Sensor Interface:

• Control Interface: A total of three pins (GND, VCC, SIG), GND to ground, VCC is the power supply, SIG digital signal output pin
• Power Indicator: Green LED, power on the right that is shiny
• Touch area: Similar to a fingerprint icon inside the area, you can touch the trigger finger.
• The positioning of the module is easy to install, to achieve inter-module combination.

Additional Information:

• Item Code: SEES-3665
• Production Capacity: 1000 NOS
• Delivery Time: 1-2 DAYS
• Packaging Details: Carton Boxes

QUICK OVERVIEW

1. Power supply: 4.5V – 5.5V, 3.3V voltage regulator circuit board
2. Positioning holes: 4 M2 screws positioning hole diameter of 2.2mm
3. Control Interface: GND, VCC, MISO, MOSI, SCK, CS
4. Size: 45 x 28mm
5. Net weight: 6g

Add the desired memory to your Arduino project to store the data, Media etc. Micro SD Card Reader Module also called Micro SD Adaptor which is designed for dual I/O voltages. The Module is a simple solution for transferring data to and from a standard SD card. The pinout is directly compatible with Not only with Arduino as shown in the diagram in below, but can also be used with other microcontrollers. Micro SD Card Reader Module has an SPI interface which is compatible with any sd card and it uses 5V or 3.3V power supply which is compatible with Arduino UNO/Mega.SD module has various applications such as data logger, audio, video, graphics.

There are total of six pins (GND, VCC, MISO, MOSI, SCK, CS), GND to ground, VCC is the power supply, MISO, MOSI, SCK is the SPI bus, CS is the chip select signal pin; 3.3V regulator circuit: LDO regulator output 3.3V as level converter chip, Micro SD card supply.

With this Module, general AVR microcontroller system can read the signal

Note: Product image may vary in terms of design, Colour of PCB from actual product.

Interfacing with Arduino Uno:

 

 

Features:

1. Support Micro SD Card (<=2G), Micro SDHC card (<=32G) (high-speed card)
2. The level conversion circuit board that can interface level is 5V or 3.3V
3. Power supply is 4.5V ~ 5.5V, 3.3V voltage regulator circuit board
4. Communication interface is a standard SPI interface.

 

Package Includes:

1 x Micro SD Card Reader Module

Additional Information:

• Item Code: SEES-3429
• Production Capacity: 1000 NOS
• Delivery Time: 1-2 DAYS
• Packaging Details: CARTON BOXES

QUICK OVERVIEW

1. On-board MAX485 chip, A low power consumption for the RS-485 communication, slew-rate limited transceiver.
2. A low power consumption for the RS-485 communication
3. Onboard then 5.08 (mm) pitch 2P terminal to facilitate RS-485 communication wiring.
4. Slew-rate limited transceiver
5. All pins of the chip have been lead to can be controlled through the microcontroller.
6. Convenient RS-485 communication wiring
7. Multiple Units can be connected to the same RS-485 bus wiring.
8. All Chip pins are brought out for proper controls

The MAX485 TTL To RS485 Module converts TTL signal to RS485 for long range, high data rate error prone differential communication. Digital communications networks implementing the EIA-485 standard can be used effectively over long distances and in electrically noisy environments.

Multiple receivers may be connected to such a network in a linear, multi-drop configuration. These characteristics make such networks useful in industrial environments and similar applications.

This converter lets you send and receive data using the RS485 network from your Arduino/microcontroller. Similar to Serial TTL and RS232 interfaces, the RS485 lets you transfer data between microcontrollers and devices but with extra features! RS485 is an industry standard protocol for data transfer and provides numerous advantages.

It lets you transfer data between up to 32 devices, through the same data line over a cable length of up to 1.2km (4000ft) with a maximum data rate of 10Mbit/s. This converter is designed for office and industrial applications (non-isolated) and provides superior characteristics/features normally found only on more expensive units.

Features :

1. On-board MAX485 chip, A low power consumption for the RS-485 communication, slew-rate limited transceiver.
2. A low power consumption for the RS-485 communication
3. Onboard then 5.08 (mm) pitch 2P terminal to facilitate RS-485 communication wiring.
4. Slew-rate limited transceiver
5. All pins of the chip have been lead to can be controlled through the microcontroller.
6. Convenient RS-485 communication wiring
7. Multiple Units can be connected to the same RS-485 bus wiring.
8. All Chip pins are brought out for proper controls

Package Includes :

1 x MAX485 TTL TO RS485

Additional Information:

• Item Code: SEES-3576
• Production Capacity: 1000 NOS
• Delivery Time: 1-2 Days
• Packaging Details: Carton Boxes

QUICK OVERVIEW

1. Standard interface layout, compatible with a variety of Arduinos such as the Pro Mini
2. Original FTDI FT232 chip, stable performance
3. USB power has current protection, using 500MA self-restore fuse
4. RXD/TXD transceiver communication indicator
5. With power, sending, receiving indicator, working status LED indicators
6. Mini USB Port Connection
7. Support 3.3V, 5V

The USB TO UART TTL 5V 3.3V FT232RL Download Cable To Serial Adapter Module is a basic breakout board for the FTDI FT232RL USB to serial IC, Revision 2. The pinout of this board matches the FTDI cable to work with official Arduino and cloned 5V Arduino boards. It can also be used for general serial applications.

The major difference with this board is that it brings out the DTR pin as opposed to the RTS pin of the FTDI cable. The DTR pin allows an Arduino target to auto-reset when a new Sketch is downloaded. This is a really nice feature to have and allows a sketch to be downloaded without having to hit the reset button. This board will auto reset any Arduino board that has the reset pin brought out to a 6-pin connector.

The pins labelled BLK and GRN correspond to the coloured wires on the FTDI cable. The black wire on the FTDI cable is GND, green is CTS. Use these BLK and GRN pins to align the FTDI basic board with your Arduino target.

This board has TX and RX LEDs that make it a bit better to use over the FTDI cable. You can actually see serial traffic on the LEDs to verify if the board is working.

This board was designed to decrease the cost of Arduino development and increase ease of use (the auto-reset feature rocks!). Our Arduino Pro boards and LilyPads use this type of connector.

One of the nice features of this board is a jumper on the back of the board that allows the board to be configured to either 3.3V or 5V (both power output and IO level). This board ship default to 5V, but you can cut the default trace and add a solder jumper if you need to switch to 3.3V.

How to interface with the Pro Mini Module:

      FTDI—–>Pro Mini

1. GND—->GND
2. VCC—->VCC
3. TX—–> RX
4. RX—-> TX
5. DTR—->GRN

 

Features :

1. Standard interface layout, compatible with a variety of Arduinos such as the Pro Mini
2. Original FTDI FT232 chip, stable performance
3. USB power has current protection, using 500MA self-restore fuse
4. RXD/TXD transceiver communication indicator
5. With power, sending, receiving indicator, working status LED indicators
6. With 3.3V and 5V TTL Level supply options
7. USB to serial TTL module, download STC SCM
8. Mini USB Port Connection
9. Support 3.3V, 5V

Package Includes :

1 x USB TO UART TTL 5V 3.3V FT232RL Download Cable To Serial Adapter Module

Additional Information:

• Item Code: SEES-1312
• Production Capacity: 1000 NOS
• Delivery Time: 1-2 Days
• Packaging Details: Carton Boxes

Thermal printers are those printers which uses heat against a special paper inorder to burn the image.

Thermal printer has a number of advantages over traditional printing techniques. The main advantage is that thermal printers are very fast and it has very quiet operation. Also thermal printers have very limited number of mechanical parts compared to traditional printers.

RP203 Technical parameters:

•   Print method:Direct thermal print and auto paper feed.
•     Printing Width: 48 MM.
•     Max Printer Speed: 85 mm/s (max).
•     Printer Interface: TTL/RS232,
•     Command System: ESC/ WH,
•     Working Voltage: DC3.3V-9V,15V,
•     Rich graphics/curve/text printing function,
•     Printing head lifespan: >50KM,
•     Paper Type: Thermal paper (With 58mm, Thickness 65+5um, diameter 35mm),
•     Printer dimension: 76.8*77.4*43.5mm(w*h*d),

Applications:

• Use this printer in any project where you need a hard-copy of the output.
•  To build a DIY cash register.

Additional Information:

• Item Code: SEES-3574
• Production Capacity: 1000 NOS
• Delivery Time: 1-2 DAYS
• Packaging Details: Carton Boxes

The 7 Segment 4 Digit Multiplexed Display have surface painted in neutral gray for enhanced on/off contrast. All devices are available in either common anode or common cathode configuration with untinted segments.

Features:

• Excellent appearance
• Evenly illuminated segments
• Gray face for optimum on/off contrast

 

 

Additional Information:

• Item Code: SEES-1536
• Production Capacity: 1000 NOS
• Delivery Time: 1-2 DAYS
• Packaging Details: Carton Boxes

QUICK OVERVIEW

1. Ultra-thin design & adhesive backing provides easy integration to any project
2. Excellent price-performance ratio
3. Easy communication with any microcontroller
4. 5 pins 2.54mm pitch connector, 4x 4type 16 keys.
5. Sticker can peel off for adhesive mounting.
6. Operating Voltage (V): 12 DC

This DC 12V 4×4 Matrix Keypad Membrane Switch is high-quality soft touch feeling button keypad with 100 million life-stroke lifespans and good resistance to environmental conditions.

This DC 12V 4×4 Key Matrix Membrane Switch Keypad is a high-quality product at very low cost for your application needs.

This 16-button keypad provides a useful human interface component for microcontroller projects. Convenient adhesive backing provides a simple way to mount the keypad in a variety of applications.

The Keypad 4×4 features a total of 16 buttons in Matrix form. This is a membrane keypad with no moving parts. A female 8-pin berg connector is require for interfacing it with your microcontroller circuits.

Features :

1. Ultra-thin design & adhesive backing provides easy integration to any project
2. Excellent price-performance ratio
3. Easy communication with any microcontroller
4. 5 pins 2.54mm pitch connector, 4x 4type 16 keys.
5. Sticker can peel off for adhesive mounting.
6. Used widely in industrial and home electronic equipments, instrument, etc.
7. This allows a microcontroller to ‘scan’ the 8 output pins to see which of the 16 buttons is being pressed.

Additional Information:

• Item Code: SEES-3376
• Production Capacity: 1000 NOS
• Delivery Time: 1-2 DAYS
• Packaging Details: Carton Boxes

QUICK OVERVIEW

1. 4×4 Matrix Keyboard Module with 16 buttons
2. Small in size and hence Save space
3. More convenient to use
4. Expanded development application modules for single chip
5. With 16 keys and 8 pin

The 4 x 4 matrix keypad usually is used as input in a project. It has 16 keys in total, which means the same input values. The 4 x 4 Matrix Keypad Module is a non-encoded matrix keypad consisting of 16 keys in parallel. The keys of each row and column are connected through the pins outside – pin R1-R4 as labeled beside control the rows, when L1-L4, the columns.

A 4×4 matrix keypad consisting of microswitch buttons. The module has four holes 3mm (M3) holes for mounting. The pin designations on each PCB are shown on each PCB. Four pins are thus used as an ‘x’ coordinate and the other 4 as a ‘y’ coordinate.
The module is already equipped with a soldered pin-headers.

How it Works:

First test whether any key is pressed down. Connect power to rows, so they are High level. Then set all the rows R1-R4 as Low and then detect the status of the columns. Any column of Low indicates there is key pressing and that the key is among the 4 keys of the column. If all columns are High, it means no key is pressed down. Next, locate the key. Since the column in which the pressed key lies is identified, knowing the line would finalize the testing. Thus, set the rows as Low in turns until any is unveiled accordingly – other rows will still be High.
Now the row can be identified. Detect the status of each column in turns. The column tested Low is the one intersecting with the line – their cross point is just the key pressed.

Features:

1. 4×4 Matrix Keyboard Module with 16 buttons
2. Small in size and hence Save space
3. More convenient to use
4. Expanded development application modules for single chip
5. With 16 keys and 8 pin

Package Includes:

1 x 4×4 Matrix 16 Keypad Keyboard Module 16 Button MCU

Additional Information:

• Item Code: SEES-3377
• Production Capacity: 1000 NOS
• Delivery Time: 1-2 DAYS
• Packaging Details: Carton Boxes

QUICK OVERVIEW

1. Ultra-thin design & adhesive backing provides easy integration to any project
2. Excellent price-performance ratio
3. Easy communication with any microcontroller
4. Mount Style: Self-Adherence
5. Max. Circuit Rating: 35 VDC, 100 mA.
6. Contact Bounce : <=5ms
7. Life Expectancy : 1 million closures
8. Operation Temperature : -20 to +40 °C

DC 12V 1×4 Key Matrix Membrane Switch Keypad is a high-quality product at a very low cost for your application needs.

This 4-button keypad provides a useful human interface component for microcontroller projects. Convenient adhesive backing provides a simple way to mount the keypad in a variety of applications.

The Keypad 1×4 features a total of 4 buttons in Matrix form. This is a membrane keypad with no moving parts. A female 5-pin berg connector is required for interfacing it with your microcontroller circuits.

Features :

1. Ultra-thin design & adhesive backing provides easy integration to any project
2. Excellent price-performance ratio
3. Easy communication with any microcontroller
4. This allows a microcontroller to ‘scan’ the 5 output pins to see which of the 4 buttons is being pressed.

Additional Information:

• Item Code: SEES-3374
• Production Capacity: 1000 NOS
• Delivery Time: 1-2 DAYS
• Packaging Details: Carton Boxes

QUICK OVERVIEW

1. Fully compliant USB 2.0 standard, backward compatible with USB1.1
2. Support System: Windows XP, Vista, Windows 7, Linux, MacOS, and WinCE5.0 drive
3. Baud Rate Range: 75bps – 115200bps, up to 6Mbps
4. Supports Plug, Play and hot-swap ( USB side)
5. Better than using CH341D chip or similar chip to support the laptop USB port.
6. Communication distance up to 1.2KM

The USB to RS485 Converter Adapter module support WIN7 XP Vista Linux Mac OS  provides an easy to use RS485 interface by means of a Virtual Com Port on the user’s system.

There are no command structures, whatever is sent to the Virtual Comm Port is automatically converted to RS485 and vice versa. The module is completely self-powered from the USB bus.

Controlling / Communicating with RS-485 devices from your PC has never been easier! This device is plug-and-play. It shows up as a serial/com port and is accessible from applications or hyper-terminal.

This converter provides half-duplex RS-485 communication. The Baud rate range is 75 bps to 115200 bps, maximum up to 6 Mbps. No need of external power supply for operation.

Applications :

1. All kinds with RS485 port device parameter settings, data communication
2. LED display of communication data
3. Machine PLC data reading and writing
4. Monitoring data read and write, and PTZ control
5. Centralized control of household electrical appliances
6. Access Control System card

Features :

1. Fully compliant USB 2.0 standard, backward compatible with USB1.1
2. Support System: Windows XP, Vista, Windows 7, Linux, MacOS, and WinCE5.0 drive
3. Supports Plug, Play and hot-swap ( USB side) ;
4. Better than using CH341D chip or similar chip to support the laptop USB port.
5. Communication distance up to 1.2KM, with the anti-jamming performance of the industrial site
6. No need external power, powered by USB port

Package Includes :

1 x USB to RS485 Converter Adapter

Additional Information:

• Item Code: SEES-3690
• Production Capacity: 1000 NOS
• Delivery Time: 1-2 Days
• Packaging Details: Carton Boxes

Feedback from our sales, not suitable for: plotter, carving machine, fiscal processor, and Doesnot support WIN8

It works on the following Operating Systems.
Windows:98/Me/2000/XP/Server2003/Vista/64bit Vista/Server2008/Win7/64bit Win7

• USB1.1/2.0 compliant solutions
• Built in 128 byte 128 byte TX/RX buffer
• Support automatic handshake protocol
• support full speed USB data transfer protocol
• Resistance to electromagnetic interference.
• Designed for Data exchange applications.

QUICK OVERVIEW

1. Single crystal 12M Tablet 340 USB port to serial port communication.
2. USB1.1/2.0 compliant solution.
3. Built-in 128 byte TX/512 byte RX buffer.
4. Supports auto-Handshake Protocol.
5. Support Win95/98/98se/ME/2000/XP/win7 32bit 64bit/Vista/supports full speed USB data transfer protocol.
6. Design of electromagnetic interference.
7. Data Exchange application.

Additional Information:

• Item Code: SEES-3691
• Production Capacity: 1000 NOS
• Delivery Time: 1-2 Days
• Packaging Details: CARTON BOXES

Product Details:

• Connect devices with a such as switches, routers
• Barcode scanners and network storage devices   
• Self Powered Through  USB    
• 9Pin D type male Connecter For Rs232O/p
• Connects 9-pin serial device to computer or laptop USB-A port

Additional Information:

• Item Code: SEES-1306
• Production Capacity: 1000 NOS
• Delivery Time: 1-2 DAYS
• Packaging Details: Carton Boxes

Secure your project with biometrics - this all-in-one optical fingerprint sensor will make adding fingerprint detection and verification super simple. These modules are typically used in safes - there's a high powered DSP chip that does the image rendering, calculation, feature-finding and searching. 1. High-Speed, High-Accuracy Fingerprint Identification 2. Download Fingerprint Images from the Device 3. Read and Write Fingerprint Templates and Databases 4. Simple UART protocol (Default 9600 baud) 5. Capable of 1:1 Verification and 1:N Identification Connect to any microcontroller or system with TTL serial, and send packets of data to take photos, detect prints, hash and search. There's a red LED in the lens that lights up during a photo so you know its working. It’s easy to use, it also comes with fairly straight-forward Windows software that makes testing the module simple – you can even enroll using the software and see an image of the fingerprint on your computer screen.

Additional Information:

• Item Code: SEES-1281
• Production Capacity: 1000 Nos
• Delivery Time: 1-2 DAYS
• Packaging Details: Carton Boxes

DIY 3-Axis Control Palletizing Robot Arm Model With Servos And Servo Arm Plate For Arduino UNO MEGA2560 Smart Robot Car.

Features:
1. 3-DOF manipulator! Vertical arm up and down, back and forth.
2. U-type robot waist bracket on the arm can be mounted directly on the base in the car or any other desktop platform.
3. The vehicle type 3-DOF manipulator medium length, back and forth up and down, in which a mechanical claw opening and closing of the steering gear control, two servo control arm up and down back and forth.
4. This robot is particularly suitable as a vehicle manipulator robot car, grab the ball, catch the car are particularly good, very suitable for their own DIY or robotic smart car racing.
5. Activities can use 180 degree steering joints.

Mechanical parameters :
1. Turning radius: 240mm.
2. Height: 290mm (gripper closed).
3. Front clamp maximum opening: 55mm.
4. Needs 3 Metal rudder.

Items included:
1. 2 x Multi-functional servo bracket.
2. 1x Long U-type servo bracket.
3. 1 x L-type servo bracket.
4. 1 x U-type robot waist bracket.
5. 1 x Aluminium Clamp Claw.
6. 3 x Metal Servo Arm plate.
7. 1 x Miniature Ball Radial Bearing.
8. 1 x Screw and screw cap set.
(Not assembled, just a kit)
Get Best Price Of DIY 3-Axis Robotic Arm For Rs.3300/-

Additional Information:

• Item Code: SEES-3854
• Production Capacity: 1000 NOS
• Delivery Time: 1-2 DAYS
• Packaging Details: CARTON BOXES

This is a 12V 16 Channel Relay Module with Light Coupling LM2576 Power Supply, Be able to control various appliances and other equipment with a large current. It can be controlled directly by Micro-controller (Arduino, 8051, AVR, PIC, DSP, ARM, MSP430, TTL logic).

This is 12V 16-Channel Relay interface board and each one of the individual relays needs 15-20mA Driver Current. The board features indication LED for Relay output status and the standard interface that can be controlled directly by many of widely used microcontrollers like Arduino etc.

The 12V electromechanical relay module with AC contact capacity of 250V which also include light coupling protection(optocoupler) for isolation of control circuitry. The plate load power module doesn’t need an external power supply. It supports all SCM Drive.

The LM2596S buck chip in this relay module shows a slight fever which is a normal phenomenon as relays, long working hours have normal fever characteristics. 4 relay load power to give leave some margin, should avoid high-power (about 2000W) and long working environment, there will be some impact on the life of the product.

Features :

1. 12V relay with AC contact capacity of 10A 250V and optocoupler protection.
2. Onboard power supply module does not need an external power supply. I / O port driver is active low.
3. The module can be used as microcontroller development board module and also as appliance control, PLC extended output.
4. It is using the industry’s top -quality isolation optocouplers, strong anti-jamming ability, stable performance.
5. The 1-16 road can be any full on/off or any road.
6. Each relay common terminal “COM” are independent, user-friendly access to different signals, each relay are normally closed and normally open with the port.
7. Each relay is equipped with motion lights.
8. All interfaces can be directly connected through the terminal leads, very convenient.

 QUICK OVERVIEW

1. 12V relay with AC contact capacity of 10A 250V and optocoupler protection.
2. Onboard power supply module does not need an external power supply. I / O port driver is active low.
3. The module can be used as microcontroller development board module and also as appliance control, PLC extended output.
4. It is using the industry’s top -quality isolation optocouplers, strong anti-jamming ability, stable performance.
5. The 1-16 road can be any full on/off or any road.
6. All interfaces can be directly connected through the terminal leads, very convenient.

Package Includes :

1 x 12V 16 Channel Relay Module with Light Coupling LM2576 Power Supply

Additional Information:

• Item Code: SEES-3010
• Production Capacity: 1000 NOS
• Delivery Time: 2-3 DAYS
• Packaging Details: CARTOON BOXES

This is a 5V 16 Channel Relay Module with Light Coupling LM2576 Power Supply, Be able to control various appliances and other equipment with a large current. It can be controlled directly by Micro-controller (Arduino, 8051, AVR, PIC, DSP, ARM, MSP430, TTL logic).

This is 5V 16-Channel Relay interface board and each one of the individual relays needs 15-20mA Driver Current. The board features indication LED for Relay output status and the standard interface that can be controlled directly by many of widely used microcontrollers like Arduino etc.

The 5V electromechanical relay module with AC contact capacity of 250V which also include light coupling protection(optocoupler) for isolation of control circuitry. The plate load power module doesn’t need an external power supply. It supports all SCM Drive.

The LM2596S buck chip in this relay module shows a slight fever which is a normal phenomenon as relays, long working hours have normal fever characteristics. 4 relay load power to give leave some margin, should avoid high-power (about 2000W) and long working environment, there will be some impact on the life of the product.

Features :

1. 5V relay with AC contact capacity of 10A 250V and optocoupler protection.
2. Onboard power supply module does not need an external power supply. I / O port driver is active low.
3. The module can be used as a microcontroller development board module and also as appliance control, PLC extended output.
4. It is using the industry’s top -quality isolation optocouplers, strong anti-jamming ability, stable performance.
5. The 1-16 road can be any full on/off or any road.
6. Each relay common terminal “COM” are independent, user-friendly access to different signals, each relay are normally closed and normally open with the port.
7. Each relay is equipped with motion lights.
8. All interfaces can be directly connected through the terminal leads, very convenient.

QUICK OVERVIEW

1. 5V relay with AC contact capacity of 10A 250V and optocoupler protection.
2. Onboard power supply module does not need an external power supply. I / O port driver is active low.
3. The module can be used as a microcontroller development board module and also as appliance control, PLC extended output.
4. It is using the industry’s top -quality isolation optocouplers, strong anti-jamming ability, stable performance.
5. The 1-16 road can be any full on/off or any road.
6. All interfaces can be directly connected through the terminal leads, very convenient.

Package Includes :

1 x 5V 16 Channel Relay Module with Light Coupling LM2576 Power Supply

Additional Information:

• Item Code: SEES-3011
• Production Capacity: 1000 NOS
• Delivery Time: 2-3 DAYS
• Packaging Details: CARTOON BOXES

This is a 2,4&8-ChannelRelay interface board that allows you to control various appliances, and other equipment’s with large current. It can be controlled directly by Micro-controller (Arduino, Raspberry Pi, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic).

Features:

1. 2,4&8-Channel Relay interface board and each one needs 15-20mA Driver Current.
2. Both controlled by 12V  input Voltage.
3. Equipped with high-current relay, AC250V 10A ; DC30V 10A.
4. Standard interface that can be controlled directly by microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic active low).
5. Indication LED’s for Relay output status.

Additional Information:

• Item Code: SEES-3035
• Production Capacity: 1000 NOS
• Delivery Time: 1-2 DAYS
• Packaging Details: CARTOON BOXES

QUICK OVERVIEW

1. Adopt imported controller PL2303HX, which can stabilize the flash with high speed
2. 500mA self-recovery fuse for protection
3. Two data transmission indicator can monitor data transfer status in real time
4. Reserve 3.3V and 5V pin interface, easy for the DDWRT of different voltage system that needs power
5. The entire board is coated by the high quality transparent heat-shrinkable sleeve, making the PCB in insulation state from outside,
6. so that the board won’t be burnt down by material shortcut.
7. Electrostatic package ensures the board will not be damaged before use

This is PL2303 PL2303HX USB To TTL(Serial) Converter Module – 5 Pin. Adopt imported controller RS232 TTL, which can stabilize the flash with high-speed 500mA self-recovery fuse for protection.

Two data transmission indicator can monitor data transfer status in real-time. Reserve 3.3V and 5V pin interface, easy for DDWRT of different voltage system that needs power. The entire board is coated by a high quality transparent heat-shrinkable sleeve, making the PCB in insulation state from outside, so that the board won’t be burnt down by a material shortcut.

Applications :

1. All kinds of satellite set-top box upgrade.
2. Router, HDD, ADSL, broadband modem firmware upgrade or cracked upgrade.
3. cellphone, XBOX360, GPS serial communication, vehicle inspection and test, DVD flash and so on.
4. Burn writes STC MCU, NXP MCU, Renesas MCU, NEC MCU and so on.
5. Simple UART communication commonly used UART debugging tools in the supper terminal.
6. USB signal transferred to the TTL signal may be used by electronic enthusiasts.

Features : 

1. Adopt imported controller PL2303HX, which can stabilize the flash with high speed
2. 500mA self-recovery fuse for protection.
3. Two data transmission indicator can monitor data transfer status in real time.
4. Reserve 3.3V and 5V pin interface, easy for the DDWRT of different voltage system that needs power.
5. The entire board is coated by the high quality transparent heat-shrinkable sleeve, making the PCB in insulation state from outside.
6. so that the board won’t be burnt down by material shortcut.
7. The electrostatic package ensures the board will not be damaged before use.
8. Support WIN7 system.

Package Includes :

1 x PL2303 PL2303HX USB To TTL Module.

Additional Information:

• Item Code: SEES-3695
• Production Capacity: 1000 NOS
• Delivery Time: 1-2 DAYS
• Packaging Details: Carton Boxes

Features:

• Inputs Connected through Burg Stick.
• Logical Data High or Low

Additional Information:

• Item Code: SEES-1550
• Production Capacity: 1000 NOS
• Delivery Time: 1-2 DAYS
• Packaging Details: Carton Boxes

QUICK OVERVIEW

1. Operating Voltage: 12V DC
2. Lifting Capacity: 2.5 KG
3. Size (D x L): 20x 15 mm
4. Electric lifting magnet.
5. Powerful and compact.
6. Smooth and flat surface.
7. Low consumption and reliable.
8. Ambient temperature within 130 degrees.

This DC 12V KK-P20/15 2.5KG Lifting Solenoid Electromagnet consists of an iron core and a coil to attract magnetic substances, using the magnetic action induced by electric current, only while the current is applied. This compact functional device offers high power with high reliability. The structure and design to release the residual magnetism left after de-energization is also one of its unique features.

Working Principle:

An electromagnet is simply a coil of wire.  It is usually wound around an iron core.  However, it could be wound around an air core, in which case it is called a solenoid.  When connected to a DC voltage or current source, the electromagnet becomes energized, creating a magnetic field just like a permanent magnet.   The magnetic flux density is proportional to the magnitude of the current flowing in the wire of the electromagnet.

We supply many varieties of electromagnets with a higher power as well as lower, original dimensions, etc to satisfy your unique requirements.

Note: Images may be seen different from actual product in terms of Dimensions

Precaution:

Electromagnets must meet the following conditions to achieve maximum suction:

1. The object to be sucked must have a good magnetic permeability.
2. Proper use of power supply, rated voltage.
3. The object to be sucked must be flat and clean.
4. The object to be sucked must be greater than or equal to the surface of the magnet( For example the magnet is 20 x 15 mm, so the surface area is S=r²π=10²π mm² so the object to be sucked must be greater than or equal to 10²π mm² )
5. The object to be sucked must be greater than 5mm. (If the thickness decreases, the suction decreases)
6. The object to be sucked must be close, the middle can’t be interspersed with objects or gaps
7. Suction means more than 5cm in thickness, surface roughness, the surface is greater than the cross-sectional area of the electromagnet and maximum suction completely fit together on an iron-based material.
8. Electromagnet in working condition electromagnetic conversion would produce a certain amount of heat, electricity more frequently the higher temperature, which is a normal phenomenon.

Features:1. Our DC-powered electromagnet generates a magnetic field of high-power with high efficiency.2. Minimized in residual magnetic.

When an electromagnet is energized, the problem is how to release the magnetic force which remains on the device after the power is turned off. Our electromagnet is designed with measures to release and minimize this residual magnetic force.

3. Lightweight, compact design for space-saving.

Compact mechanism with high reliability.

4. Long life

High mechanical strength and excellent durability.

5. Widely applied in automation: assembly line, sorting machine, mechanical arm, experimental facility, etc

 

Package Includes:

1 x DC 12V KK-P20/15 2.5KG Lifting Solenoid Electromagnet

1 x M4 Bolt with Washer

Additional Information:

• Item Code: SEES-3497
• Production Capacity: 1000 NOS
• Delivery Time: 1-2 DAYS
• Packaging Details: CARTON BOXES