Sri Electronics & Embedded Solutions

The PICKIT2 Programmer and Debugger is a low-cost in-circuit debugger (ICD) and in-circuit serial programmer (ICSP). Pickit 2 is intended to be used as an evaluation, debugging and programming aid in a laboratory environment. The Pickit 2 offers these features: Real-time and single-step code execution Breakpoints, Register and Variable Watch/Modify.

Features:

• PICKIT2 Programmer and Debugger
• In-circuit debugging.
• Target VDD monitor.
• Diagnostic LEDs.
• MPLAB IDE user interface.
• USB interface to a host PC / USB Powered.
• 40 Pin Target Board With FRC Cable.
• ICSP FRC connecter Easy to interface to all our NSK boards.

 

How Pickit 2 Helps You:

• Debug your source code in your own application.
• Debug your hardware in real-time.
• Program a supported device using Microchip’s ICSP protocol through FRC cable supplied with this kit.

 

Package Content:

• Pickit2 Programmer.
• Programming Adapter Board.
• USB Port Cable.
• Software CD (Data sheets, Example Programs, Manual, MPLAB IDE).

Additional Information:

• Item Code: SEES-1140
• Port of Dispatch: Coimbatore
• Production Capacity: 1000 NOS
• Delivery Time: 1-2 DAYS
• Packaging Details: Carton Boxes

QUICK OVERVIEW

1. 5V power supplied by a USB connector
2. USB 2.0 full speed compatible interface
3. USB standard A to mini B cable
4. 1.65V to 5.5V application voltage supported on SWIM interface
5. SWIM low speed and high-speed modes supported

This is ST-LINK/V2 in-circuit debugger/programmer for STM8 and STM32.

ST-LINK/V2 is an in-circuit debugger and programmer for the STM8 and STM32 microcontroller families. The single wire interface module (SWIM) and JTAG/serial wire debugging (SWD) interfaces are used to communicate with any STM8 or STM32 microcontroller located on an application board.

STM8 applications use the USB full speed interface to communicate with ST Visual Develop (STVD) or ST Visual Program (STVP) software. STM32 applications use the USB full speed interface to communicate with Atollic, IAR, Keil or TASKING integrated development environments.

In addition, to provide the same functionalities as the ST-LINK/V2, the ST-LINK/V2-ISOL features digital isolation between the PC and the target application board. It also withstands voltages of up to 1000 Vrms.

Features :

1. 5V power supplied by a USB connector
2. USB 2.0 full speed compatible interface
3. USB standard A to mini B cable
4. 1.65V to 5.5V application voltage supported on SWIM interface
5. SWIM low speed and high-speed modes supported
6. 1.65V to 3.6V application voltage supported on the JTAG/SWD interface and 5V tolerant inputs
7. Direct firmware update feature supported
8. Status LED which blinks during communication with the PC

Package Includes :

1 x ST-LINK/V2 debugging and programming Unit

1 x USB standard A to mini B cable

1 x Connecting Cable for STM8 SWIM and STM32 JTAG/SWD protocol

1 x Flat ribbon with a standard ERNI connector at one end (A JTAG or SWD and SWV flat ribbon with a 20 pin connector)

Additional Information:

• Item Code: SEES-3634
• Production Capacity: 1000 NOS
• Delivery Time: 1-2 DAYS
• Packaging Details: Carton Boxes

QUICK OVERVIEW

Compatible Chips:

1. ATMega Series
2. Tiny Series
3. CAN Series

The USB ASP AVR Programming Device for ATMEL processors is a USB in-circuit programmer for Atmel AVR controllers. USBASP AVR PROGRAMMING DEVICE FOR ATMEL PROCESSORS simply consists of an ATMega88 or an ATMega8 and a couple of passive components. The programmer uses a firmware-only USB driver; no special USB controller is needed.

Specifications and Features :

1. MODEL NO. : USBASP AVR PROGRAMMING DEVICE FOR ATMEL PROCESSORS
2. WEIGHT & DIMENSIONS:25g
3. MATERIAL & COLOR: NA & Blue
4. COMPATIBLE CHIPS:
   1. Mega Series
   2. ATmega8 ATmega48 ATmega88 ATmega168 ATmega328
   3. ATmega103 ATmega128 ATmega1280 ATmega1281 ATmega16
   4. ATmega161 ATmega162 ATmega163 ATmega164 ATmega169
   5. ATmega2560 ATmega2561 ATmega32 ATmega324 ATmega329
   6. ATmega3290 ATmega64 ATmega640 ATmega644 ATmega649
   7. ATmega6490 ATmega8515 ATmega8535
   8. Tiny Series
   9. ATtiny12 ATtiny13 ATtiny15 ATtiny25 ATtiny26
   10. ATtiny45, ATtiny85, ATtiny88, ATtiny2313
   11. Classic Series
   12. AT90S1200 AT90S2313 AT90S2333 AT90S2343 AT90S4414
   13. AT90S4433 AT90S4434 AT90S8515
   14. AT90S8535 AT89S51 AT89S52 AT89S53 AT89S8252
   15. CAN Series
   16. AT90CAN128
   17. PWM Series
   18. AT90PWM2 AT90PWM3.

Package Includes :

1 x USB asp AVR Programming Device.

1 x FRC cable.

 

Additional Information:

• Item Code: SEES-3137
• Production Capacity: 1000 NOS
• Delivery Time: 1-2 DAYS
• Packaging Details: CARTON BOXES

The ST-LINK/V2 is an in-circuit debugger and programmer for the STM8 and STM32 microcontroller families. The single wire interface module (SWIM) and JTAG/serial wire debugging (SWD) interfaces are used to communicate with any STM8 or STM32 microcontroller located on an application board.

Much similar in architecture for debugging, the ST-LINK/V2 and the ST-LINK/V2-ISOL share the same features like digital isolation between the PC and the target application board this allows to withstands voltages of up to 1000 Vrms.

Specifically the debugger incorporates the use of USB full-speed interface to communicate with the ST Visual Develop (STVD)  or ST Visual Program (STVP) software for STM8 application, and use of the USB full-speed interface to communicate with Atollic®, IAR™, Keil®or TASKING integrated development environments for STM32 applications.

 

Specifications:-

 

• Support STM32 SWD interface debugging
• Support STM8 all series download
• Support firmware auto upgrade
• With cover case for protection, anti-dust and anti-short circuit
• Small size: 50*28*14mm

 

 

Features:-

 

• 5 V power supplied by a USB connector
• USB 2.0 full-speed-compatible interface
• USB standard A to Mini- B cable

 

 

SWIM Specific Features:-

 

• 1.65 V to 5.5 V application voltage supported on SWIM interface
• SWIM low-speed and high-speed modes supported
• SWIM programming speed rate: 9.7 Kbytes/s in low speed and 12.8 Kbytes/s in high speed
• SWIM cable for connection to the application via an ERNI standard vertical connector (ref: 284697 or 214017) or horizontal connector (ref: 214012)
• SWIM cable for connection to the application via a pin header or a 2.54 mm pitch connector

 

 

JTAG/serial wire debugging (SWD) specific features:-

 

• 1.65 V to 3.6 V application voltage supported on the JTAG/SWD interface and 5 V tolerant inputs
• JTAG cable for connection to a standard JTAG 20-pin pitch 2.54 mm connector
• JTAG supported
• SWD and serial wire viewer (SWV) communication supported
• Direct firmware update feature supported (DFU)
• Status LED which blinks during communication with the PC
• Operating temperature 0 to 50 °C
• 1000 Vrms high isolation voltage (ST-LINK/V2-ISOL only)

 

 

Package Includes:-

 

• ST-LINK V2 Emulator
• Mini USB T-plug cable
• FRC cable with 20 pin connector
• Dual Female connectors 

Additional Information:

• Item Code: SEES140
• Production Capacity: 1000 NOS
• Delivery Time: 1-2 DAYS
• Packaging Details: CARTOON BOXES

ST-Link V2 Programmer For STM8 and STM32 is fully consistent with the official version, support for automatic upgrades, support the full range STM32 SWD (only 4pins including SWCLK, SWDIO, and power) and a full range STM8 SWIM (only 4pins including SWIM, Reset and power) download and debug.

Use this device to send program code to the 32-bit STM32 ARM Cortex or 8-bit STM8 microcontrollers. The header for this ST-Link v2 programmer contains connections for 5V, 3.3V, SWCLK, SWDIO, SWIM, Reset (RST/NRST) and GND. The connector on the opposite side of this device is a USB connector and is intended to be plugged into the computer.

Note: The product is available in Multiple colors Will be shipped randomly.
Supports For ST-LINK V2 :

1. ST-LINK Utility 2.0 and above.
2. STVD 4.2.1 and above.
3. STVP 3.2.3 and above.
4. IAR EWARM V6.20 and above.
5. IAR EWSTM8 V1.30 and above.
6. KEIL RVMDK V4.21 and above.

Features :

1. PCB installed inside of aluminum alloy U disk shell, portable, safe and reliable!
2. Interface definition directly marked on the shell, clear, convenient and practical!
3. 5V, 3.3V offers at the same time, allowing you to program your target board with both 5V and 3.3V
4. Shell characters using laser engraving, never fade off! Permanent clarity!
5. 500MA internal resettable fuse, complete protection of your expensive computer motherboard!
6. Red and blue color LED indicator, allowing you to always observe ST-LINK V2 working condition!
7. With4 DuPont line, so you can easily respond to different target board line order!
8. Use anti-static bag packaging.
9. SWIM specific features:
   • SWIM cable for connection to the application via a pin header or a 2.54 mm pitch connector
   • 1.65 V to 5.5 V application voltage supported on SWIM interface
   • SWIM low-speed and high-speed modes supported
   • SWIM programming speed rate: 9.7 Kbytes/s in low speed and 12.8 Kbytes/s in high speed
   • SWIM cable for connection to the application
10. Direct firmware update feature supported (DFU)
11. Status LED which blinks during communication with the PC
12. Operating temperature 0 to 50C

Package Includes:

1 xST-Link V2 Programmer For STM8 and STM32.

1 x Connecting Wires.

Specifications:-

Additional Information:

• Item Code: SEES-3635
• Production Capacity: 1000 NOS
• Delivery Time: 1-2 DAYS
• Packaging Details: CARTON BOXES

QUICK OVERVIEW

1. Full-speed USB support using Windows standard drivers
2. Real-time execution
3. Processors run at maximum speeds
4. Built-in over-voltage/short circuit monitor
5. Low voltage to 5V (1.8 to the 5V range)
6. Read/write program and data memory of the microcontroller
7. Program up to 512K byte flash.

This is PICkit3 PIC KIT3 Debugger Programmer Emulator Controller Development board. USB connection is more stable than ICD2. Offline burning function. Develop debug programming, do product batch offline burning or make. Power supply input, the inner voltage can be controlled by MPLAB IDE directly.

PICKIT3.5, begin to support Win7 system. Full patch design, patch through the reflow soldering processing, more stable quality. PIC developing data, C language development tool manual. A lot of PIC basic experiment program code; ICD2 PICKIT3 etc application specification.

The MPLAB PICkit 3 allows debugging and programming of PIC® and dsPIC® Flash microcontrollers at a most affordable price point using the powerful graphical user interface of the MPLAB Integrated Development Environment (IDE). The MPLAB PICkit 3 is connected to the design engineer’s PC using a full speed USB interface and can be connected to the target via a Microchip debug (RJ-11) connector (compatible with MPLAB ICD 2, MPLAB ICD 3 and MPLAB REAL ICE).

Features :

1. Full-speed USB support using Windows standard drivers
2. Real-time execution
3. Processors run at maximum speeds
4. Built-in over-voltage/short circuit monitor
5. Low voltage to 5V (1.8 to the 5V range)
6. Read/write program and data memory of the microcontroller
7. Diagnostic LEDs (power, active, status)
8. Read/write program and data memory of the microcontroller
9. 1Erase of all memory types (EEPROM, ID, configuration, and program) with verification
10. Peripheral freeze at the breakpoint.
11. Program up to 512K byte flash.

Package Includes :

1 x PIC KIT3

1 x USB cable

1 x 6pin cable

Additional Information:

• Item Code: SEES-3508
• Production Capacity: 1000 NOS
• Delivery Time: 1-2 DAYS
• Packaging Details: Carton Boxes