Sri Electronics & Embedded Solutions

Float Sensor is an electrical ON/OFF Switch, which operates automatically when liquid level goes up or down with respect to specified level. The Signal thus available from the Float Sensor can be utilized for control of a Motor Pump or an allied electrical element like Solenoid, Lamps, and Relays etc.

Float Sensors contain hermetical sealed Reed Switch in the stem and a permanent Magnet in the Float. As the Float rises or falls with the level of liquid the Reed Switch is activated by Magnet in the Float.

Working:

Available either Normally Open, Normally Close, Change Over Contact Form.

Application:

• House hold Equipments such as overhead water tanks,Water purifiers.

How Magnetic Reed Liquid Level Sensors Work

The purpose of a float switch is to open or close a circuit as the level of a liquid rises or falls. Most float switches are "normally closed," meaning the two wires coming from the top of the switch complete a circuit when the float is at its low point, resting on its bottom clip or stop (for example, when a tank is dry).


Most float switches utilize a magnetic reed switch to open or close the circuit. The reed is encased in a glass tube, which is cemented into a plastic or stainless steel stem with epoxy. The illustration to the left demonstrates how a magnet can be used to open or close a circuit by moving it closer to or farther away from a reed switch.

When the magnet comes close to the two contacts, they draw together and touch, allowing current to pass through. When the magnet is moved away, the contacts demagnetize and separate, breaking the circuit.

In a float switch, the magnetic reed switch is hermetically sealed in a stem, most often made from plastic or stainless steel. The float encases a sealed magnet, which moves up and down the length of the stem as a fluid level rises and falls.

As the magnet passes by the contacts in the encased reed switch, they draw together and complete a circuit between the two lead wires, as shown in the cutaway to the left.

The operation shown can usually be reversed by removing the bottom clip from the switch, inverting the float and replacing the clip. When this change is made, the switch circuit will be open when the float is resting on the bottom clip and closed when the float rises.

Properly used, float switches can deliver millions of on/off cycles, for years of dependable operation. Failures are normally due to overloading, frequently caused by spiking voltage. Before designing a circuit which uses a float switch, be sure to read our Technical Page on Spiking Voltage & Float Switches.

 

Additional Information:

• Item Code: SEES-1484
• Port of Dispatch: Coimbatore
• Production Capacity: 1000
• Delivery Time: 2-3days

Our offered Type 1 Water Float Switch are widely used for detecting the level of liquid in tank as these switches are designed with strict compliance of precision engineering. Excellent in durability and easy installation aspects have made these products widely used in automobile industries and chemical industries. Moreover, we have with us wide configurations of these machines for supply to customers at reasonable price tags.

Features:

• High accuracy
• Superior strength
• Optimal sensitivity

Additional Information:

• Item Code: SEES-3257
• Pay Mode Terms: T/T (Bank Transfer),Other
• Port of Dispatch: Coimbatore
• Production Capacity: 1000 NOS
• Delivery Time: 1-2 DAYS
• Packaging Details: CARTON BOXES

SEES Automatic Cyclic Timer For Water Level Controller -Single phase

SEES Automatic Cyclic Timer For Water Level Controller -Single phase

Additional Information:

• Item Code: SEES-1279
• Production Capacity: 1000 NOS
• Delivery Time: 1-2 DAYS
• Packaging Details: CARTOON BOXES

QUICK OVERVIEW

1. Compact and convenient,Easily installed and serviced
2. Precise and reliable.Mechanical no power consumption,Steady flow adjustable.
3. The installation direction can be arbitrary Angle
4. Pressure regulating valve (steady flow valve) function similar to water flow switch
5. Not only can the constant current steady flow, but also prevent the dry burning and monitoring the flow

12V DC 1/2″ Electric Solenoid Water Air Valve Switch (Normally Closed)  Controls the flow of fluid+air and act as a valve between high-pressure water or any fluid! This liquid valve would make a great addition to your robotic gardening project. There are two ½” (Nominal NPT) outlets. Normally, the valve is closed. When 12Vdc is applied to the two terminals, the valve opens and water can push through.

The valve works with solenoid coil which operates electronically with DC 12 volt supply. As it is normally closed assembly, it opens the flow of liquid as soon as power ON and stops/blocks the flow when the supply voltage removed.

Suitable for liquid, water, oil, high-end water heaters, intelligent drinking fountains, water heaters, straight drinking machines, water purification machines, steam machines, Energy-saving air-conditioning, water treatment, cooling equipment and water industry and other fields, the use of a large number

Note:  Images may vary from actual product in terms of Brand as per the stock availability  

Features:

1. Compact and convenient, Easily installed and serviced
2. Precise and reliable.Mechanical no power consumption, Steady flow adjustable.
3. The installation direction can be arbitrary Angle
4. Pressure regulating valve (steady flow valve) function similar to water flow switch
5. Not only can the constant current steady flow, but also prevent the dry burning and monitoring the flow.

Additional Information:

• Item Code: SEES-3626
• Pay Mode Terms: T/T (Bank Transfer),Other
• Port of Dispatch: Coimbatore
• Production Capacity: 1000
• Delivery Time: 1-2 days
• Packaging Details: CARTON BOXES

Product description

 

SEES Automatic Water Level Controller-NEW MODEL- BORE-Single phase

Automatic Water Level Controller For Single Phase Submersible (bore well) Pumps Panel Driver (Single phase tothree phase). This is a unique device for submersible Pump Up to 2.5 HP Capacity. Our submersible panel drive is the most suitable device for start/Run capacitors Panel Driven Water Pumps. It increases the life of motor to work for year. Application Like Residential Buildings, apartment’s, Commercial Complexes, Industrial Buildings, Hotels, Hospitals, . . . .Etc.

Visual Indications :

Four stage water level indicator for over head tank, water flow indication(Running Line), voltage level indication, power on indication and auto/manual indication.

 

Features: Switch on the panel if water tank is in required mode and switch off the panel at tank full.

Dry Run
Due to faulty foot valve or air leakage in the pipe if the motor runs dry then it gets switched off
automatically and gives fault indication.

Voltage Cut-off
Automatic Water Level Controller SEES-BORE automatically switches-off the pump if the supply voltage drops below 160V or Crosses 250V.

Surge protection
Built in surge protection is the Main features of SEES series.

Toggle Bypass Switch.
The optional toggle switch is provided to bypass system operation in case of system failure. so no need to disconnect the system when it gets failed.

Power ON/OFF Switch.
Small rocker switch to select Power On/Off operation.

Application:
The product is suitable for almost all site conditions water tank for maintaining level
automatically, can be used to control water inflow or outflow, by means of direct pump control or acting as a control switch of a magnetic or combination starter.

Sutable for

Bore well submersible pumps.
Jet Pumps,
In SEES series variants are available for any type of pump, bore well and any combination of tanks.

 

 

AUTOMATIC WATER LEVEL CONTROLLER(BOREWELL)

•When overhead tank goes 20% pump starts automatically and tank full automatic pump will turn off.
•User can connect with their DOL starter.
•Dry run also available, if checks a water flow for one minute if water not flowing more than a minute pump will goes off.
•Water does not waste, and we can save electricity, and our precious time.
•2 relay based ON and OFF
•Microcontroller based controlling Applications: Home, School, Hospital, Industries, College

 

SPECIFICATION POWER INPUT :
•230v input
•12v-1A Transformer
•When the power on red led will glow RELAY :
•12v T relay: 250v 30A, 24v 30A
•Relay used :2 Channel SENSOR PINS:
•Common (com), Tank Low (TL), Tank High (TH), Dry run (DR). SENSOR TYPE:
•SS

• Brand SEES
• Model Name/Number SEES- BORE
• Operation Type Fully Automatic Tank Type Overhead Tank Phase 1-Phase
• Mounting Type  : Wall
• Type Manual, Automatic, Digital
• Range 3-5m, 5-8m, 11-15m, 8-11m
• Feature Low Temperature Resistant, Monitoring, Conductor, Corrosion Resistant
• Input Voltage 230 V
• Frequency 50 Hz
• Warranty- 1 year

Additional Information:

• Item Code: SEES-1268
• Production Capacity: 1000 NOS
• Delivery Time: 1-2 DAYS
• Packaging Details: CARTOON BOXES

QUICK OVERVIEW

1. Operating Voltage : 2.5 ~ 6V
2. Operating Current : 130 ~ 220mA
3. Flow Rate : 80 ~ 120 L/H
4. Maximum Lift : 40 ~ 110 mm
5. Outlet Outside Diameter: 7.5 mm
6. Outlet Inside Diameter: 5 mm

This DC 3-6 V Mini Micro Submersible Water Pump is a low cost, small size Submersible Pump Motor which can be operated from a 2.5 ~ 6V power supply. It can take up to 120 liters per hour with a very low current consumption of 220mA. Just connect tube pipe to the motor outlet, submerge it in water and power it.

Make sure that the water level is always higher than the motor. The dry run may damage the motor due to heating and it will also produce noise.

NOTE: This product is available in two different colours as Black and White, which will be shipped randomly.Features :

1. DC 3v to 6v submersible pump
2. micro mini submersible water pump 3v to 6v
3. DC water pump for DIY
4. DC pump for HOBBY kit.

Package Includes :

1 x DC 3-6 V Mini Micro Submersible Water Pump

Additional Information:

• Item Code: SEES-3719
• Pay Mode Terms: T/T (Bank Transfer),Other
• Port of Dispatch: Coimbatore
• Production Capacity: 1000
• Delivery Time: 1-2days
• Packaging Details: CARTON BOXES

Product description

 

FEATURES

High reliability and Low maintenance. Automatic SEES Automatic Water Level Controller-Economic Model- Sump-Single phase can be used for a long time, no maintenance or repairing would be Required during its operational period. Low AC Voltage sensing circuit to avoid polarization of electrodes in water. These special stainless steel plastic SEES molded conductive electrodes are Long life sensors and do not require frequent cleaning or replacement. Overflow prevention system provides effective and reliable Water level monitoring, with Level Indicators.

Rocker Bypass Switch.

The optional rocker switch is provided to bypass system operation in case of system failure. so no need to disconnect the system when it gets failed.

DryRun

Due to faulty foot valve or air leakage in the pipe if the motor runs dry then it gets switched off automatically and gives fault indication. For more details please watch video demo.

 

 

Sutable for

mono block pump (sump motor)
sump submersible pumps.
Jet Pumps, etc...

This Water level controllers Indicator is highly recommended for metro cities or areas where drinking water is supplied through pipelines which are further distributed in homes, hotels, societies etc.

At large our systems not only help you but your neighbours and society, also as it reduces the wastage of water by cutting down any further overflow than what you need.

 

AUTOMATIC WATER LEVEL CONTROLLER(SUMP)
•When overhead tank goes 20% pump starts automatically and when tank full automatic pump will turn off
•If sump tank also empty pump will turn off
•Dry run also available, if checks a water flow for one minute if water not flowing more than a minute pump will goes off.
•Water does not waste, and we can save electricity, and our precious time.
•SS contact sensor type.
•Microcontroller based controlling Applications: Home, School, Hospital, Industries, College.

 

SPECIFICATION POWER INPUT :
•230v input
•12v-1A Transformer
•When the power on red led will glow RELAY :
•12v T relay: 250v 30A, 24v 30A
•Relay used :1 Channel SENSOR PINS:
•Common (com), Sump Low(SL), Sump High (SH), Tank Low (TL), Tank High (TH), Dry run (DR). SENSOR TYPE:
•SS Contact type

• Model Name/Number SEES-SUMP
• Operation Type Fully Automatic Phase 1-Phase
• Range 3.1-5m, 0-3m
• Features Corrosion Resistant, Low Temperature Resistant
• Usage/Application Water Level Controller
• Input Voltage 160V - 250V
• Size 170mm x150mm x 60mm
• Warranty 1 Year
• Dry run trip delay 90 seconds.
• Power onDelay 30 seconds
• Frequency 50 Hz

Additional Information:

• Item Code: SEES-1267
• Production Capacity: 1000 NOS
• Delivery Time: 1-2 DAYS
• Packaging Details: CARTOON BOXES

Product description

 

SEES Automatic Water Level Controller-BORE -Single phase

Automatic Water Level Controller For Single Phase Submersible (bore well) Pumps Panel Driver (Single phase tothree phase). This is a unique device for submersible Pump Up to 2.5 HP Capacity. Our submersible panel drive is the most suitable device for start/Run capacitors Panel Driven Water Pumps. It increases the life of motor to work for year. Application Like Residential Buildings, apartment’s, Commercial Complexes, Industrial Buildings, Hotels, Hospitals, . . . .Etc.

Visual Indications :

Four stage water level indicator for over head tank, water flow indication(Running Line), voltage level indication, power on indication and auto/manual indication.

 

Features: Switch on the panel if water tank is in required mode and switch off the panel at tank full.

Dry Run
Due to faulty foot valve or air leakage in the pipe if the motor runs dry then it gets switched off
automatically and gives fault indication.

Voltage Cut-off
Automatic Water Level Controller SEES-BORE automatically switches-off the pump if the supply voltage drops below 160V or Crosses 250V.

Surge protection
Built in surge protection is the Main features of SEES series.

Toggle Bypass Switch.
The optional toggle switch is provided to bypass system operation in case of system failure. so no need to disconnect the system when it gets failed.

Power ON/OFF Switch.
Small rocker switch to select Power On/Off operation.

Application:
The product is suitable for almost all site conditions water tank for maintaining level
automatically, can be used to control water inflow or outflow, by means of direct pump control or acting as a control switch of a magnetic or combination starter.

Sutable for

Bore well submersible pumps.
Jet Pumps,
In SEES series variants are available for any type of pump, bore well and any combination of tanks.

 

 

AUTOMATIC WATER LEVEL CONTROLLER(BOREWELL)

•When overhead tank goes 20% pump starts automatically and tank full automatic pump will turn off.
•User can connect with their DOL starter.
•Dry run also available, if checks a water flow for one minute if water not flowing more than a minute pump will goes off.
•Water does not waste, and we can save electricity, and our precious time.
•2 relay based ON and OFF
•Microcontroller based controlling Applications: Home, School, Hospital, Industries, College

 

SPECIFICATION POWER INPUT :
•230v input
•12v-1A Transformer
•When the power on red led will glow RELAY :
•12v T relay: 250v 30A, 24v 30A
•Relay used :2 Channel SENSOR PINS:
•Common (com), Tank Low (TL), Tank High (TH), Dry run (DR). SENSOR TYPE:
•SS

• Brand SEES
• Model Name/Number SEES- BORE
• Operation Type Fully Automatic Tank Type Overhead Tank Phase 1-Phase
• Mounting Type  : Wall
• Type Manual, Automatic, Digital
• Range 3-5m, 5-8m, 11-15m, 8-11m
• Feature Low Temperature Resistant, Monitoring, Conductor, Corrosion Resistant
• Input Voltage 230 V
• Frequency 50 Hz
• Warranty- 1 year

Additional Information:

• Item Code: SEES-1269
• Production Capacity: 1000 NOS
• Delivery Time: 1-2 DAYS
• Packaging Details: CARTOON BOXES

SEES Automatic Cyclic Timer system for Water level controller- Single phase


SEES Automatic Cyclic Timer system for Water level controller- Single phase

SEES Automatic Cyclic Timer system for Water level controller- Single phase

Additional Information:

• Item Code: SEES-1270
• Production Capacity: 1000 nos
• Delivery Time: 1-2 DAYS
• Packaging Details: CARTOON BOXES

Product description

 

FEATURES

High reliability and Low maintenance. Automatic SEES Water Level Controller SEES-Sump can be used for a long time, no maintenance or repairing would be Required during its operational period. Low AC Voltage sensing circuit to avoid polarization of electrodes in water. These special stainless steel plastic SEES molded conductive electrodes are Long life sensors and do not require frequent cleaning or replacement. Overflow prevention system provides effective and reliable Water level monitoring, with Level Indicators.

Rocker Bypass Switch.

The optional rocker switch is provided to bypass system operation in case of system failure. so no need to disconnect the system when it gets failed.

DryRun

Due to faulty foot valve or air leakage in the pipe if the motor runs dry then it gets switched off automatically and gives fault indication. For more details please watch video demo.

VoltageCut-off

Automatic Water Level Controller SEES-S automatically switches-off the pump if the supply voltage drops below 160V or Crosses 250V.

 

Sutable for

mono block pump (sump motor)
sump submersible pumps.
Jet Pumps, etc...

This Water level controllers Indicator is highly recommended for metro cities or areas where drinking water is supplied through pipelines which are further distributed in homes, hotels, societies etc.

At large our systems not only help you but your neighbours and society, also as it reduces the wastage of water by cutting down any further overflow than what you need.

 

AUTOMATIC WATER LEVEL CONTROLLER(SUMP)
•When overhead tank goes 20% pump starts automatically and when tank full automatic pump will turn off
•If sump tank also empty pump will turn off
•Dry run also available, if checks a water flow for one minute if water not flowing more than a minute pump will goes off.
•Water does not waste, and we can save electricity, and our precious time.
•SS contact sensor type.
•Microcontroller based controlling Applications: Home, School, Hospital, Industries, College.

 

SPECIFICATION POWER INPUT :
•230v input
•12v-1A Transformer
•When the power on red led will glow RELAY :
•12v T relay: 250v 30A, 24v 30A
•Relay used :1 Channel SENSOR PINS:
•Common (com), Sump Low(SL), Sump High (SH), Tank Low (TL), Tank High (TH), Dry run (DR). SENSOR TYPE:
•SS Contact type

• Model Name/Number SEES-SUMP
• Operation Type Fully Automatic Phase 1-Phase
• Range 3.1-5m, 0-3m
• Features Corrosion Resistant, Low Temperature Resistant
• Usage/Application Water Level Controller
• Input Voltage 160V - 250V
• Size 170mm x150mm x 60mm
• Warranty 1 Year
• Dry run trip delay 90 seconds.
• Power onDelay 30 seconds
• Frequency 50 Hz

Additional Information:

• Item Code: SEES-1266
• Production Capacity: 1000 NOS
• Delivery Time: 1-2 DAYS
• Packaging Details: CARTOON BOXES

SEES  Wireless (RF-BASED)Automatic Water Level Controller-Sump-Single phase

Wireless (RF-BASED)Automatic Water Level Controller
 
    Product Descriptions :

433 MHZ RF Transmitter & Receiver, 90 meter range.

it also work if there is obstacle between the transmitter and receiver.

High quality ABS plastic Enclosure.

Working : This model automatically switches ON and OFF Motor.

When the water level of the overhead tank becomes low means water gets down from the middle sensor and water is present in the underground tank or sump, the motor gets started automatically. The tank starts filling up. when the water level reaches to the higher level, the motor automatically gets switched off.

AUTO OFF WHEN TANK IS FULL OR SUMP IS EMPTY.

This model has dry run protection so it only starts the motor if water is present in the underground tank or sump.

Suitable for 0.1 HP to 5.0 HP Motor, Protect motor from dry running.

Motor ON OFF LED indication provided.

Water Level indication provided for both tanks.

Auto and manual mode indication provided 

Supply voltage : 220-270 V AC,

Relay : 40 A

Sensing element : S.S sensor

Auto and Manual mode switch available. In auto mode the motor starts and stops automatically. In manual mode the user can start and stop the motor by pressing the start and stop button of the controller. No additional wiring is required to operate the motor manually. 

Also Suitable for MCB Starter panel and submersible motor, see diagram above for connection.

High quality ABS enclosure provided.

Fully automatic, controls from underground tank to overhead tank so no man power required. Long service Life.

All signals passes in sensors through the AC filter circuit that improve life of sensor,

Isolated supply provided

Sensor fault detection provided, if sensor got failed LED start blinking

Electrolysis free design 

 

Additional Information:

• Item Code: SEES-1282
• Production Capacity: 1000 nos
• Delivery Time: 1-2 DAYS
• Packaging Details: CARTOON BOXES

SEES Automatic Water Level Controller-Sump & Bore Model -Single phase

FEATURES

High reliability and Low maintenance. Automatic SEES Water Level Controller SEES-Sump can be used for a long time, no maintenance or repairing would be Required during its operational period. Low AC Voltage sensing circuit to avoid polarization of electrodes in water. These special stainless steel plastic SEES molded conductive electrodes are Long life sensors and do not require frequent cleaning or replacement. Overflow prevention system provides effective and reliable Water level monitoring, with Level Indicators.

Rocker Bypass Switch.

The optional rocker switch is provided to bypass system operation in case of system failure. so no need to disconnect the system when it gets failed.

DryRun

Due to faulty foot valve or air leakage in the pipe if the motor runs dry then it gets switched off automatically and gives fault indication. For more details please watch video demo.

VoltageCut-off

Automatic Water Level Controller SEES-S automatically switches-off the pump if the supply voltage drops below 160V or Crosses 250V.

 

Sutable for

mono block pump (sump motor)
sump submersible pumps.
Jet Pumps, etc...

This Water level controllers Indicator is highly recommended for metro cities or areas where drinking water is supplied through pipelines which are further distributed in homes, hotels, societies etc.

At large our systems not only help you but your neighbours and society, also as it reduces the wastage of water by cutting down any further overflow than what you need.

 

AUTOMATIC WATER LEVEL CONTROLLER(SUMP)
•When overhead tank goes 20% pump starts automatically and when tank full automatic pump will turn off
•If sump tank also empty pump will turn off
•Dry run also available, if checks a water flow for one minute if water not flowing more than a minute pump will goes off.
•Water does not waste, and we can save electricity, and our precious time.
•SS contact sensor type.
•Microcontroller based controlling Applications: Home, School, Hospital, Industries, College.

 

SPECIFICATION POWER INPUT :
•230v input
•12v-1A Transformer
•When the power on red led will glow RELAY :
•12v T relay: 250v 30A, 24v 30A
•Relay used :1 Channel SENSOR PINS:
•Common (com), Sump Low(SL), Sump High (SH), Tank Low (TL), Tank High (TH), Dry run (DR). SENSOR TYPE:
•SS Contact type

• Model Name/Number SEES-SUMP
• Operation Type Fully Automatic Phase 1-Phase
• Range 3.1-5m, 0-3m
• Features Corrosion Resistant, Low Temperature Resistant
• Usage/Application Water Level Controller
• Input Voltage 160V - 250V
• Size 170mm x150mm x 60mm
• Warranty 1 Year
• Dry run trip delay 90 seconds.
• Power onDelay 30 seconds
• Frequency 50 Hz

 BOREWELL TO OVERHEAD TANK (SEES-BORE)

Automatic Water Level Controller For Single Phase Submersible (bore well) Pumps Panel Driver (Single phase tothree phase). This is a unique device for submersible Pump Up to 2.5 HP Capacity. Our submersible panel drive is the most suitable device for start/Run capacitors Panel Driven Water Pumps. It increases the life of motor to work for year. Application Like Residential Buildings, apartment’s, Commercial Complexes, Industrial Buildings, Hotels, Hospitals, . . . .Etc.

Visual Indications :

Four stage water level indicator for over head tank, water flow indication(Running Line), voltage level indication, power on indication and auto/manual indication.

 

Features: Switch on the panel if water tank is in required mode and switch off the panel at tank full.

 

Additional Information:

• Item Code: SEES-1280
• Production Capacity: 1000 NOS
• Delivery Time: 1-2 DAYS
• Packaging Details: CARTOON BOXES

SEES GSM Based  Automatic Water Level Controller-Motor ON/OFF Control
 
         In GSM based, the GSM Pump Controllers (Mobile Pump Starter) are specifically design to operate remote located submersible pumps and motors for benefit of farmers, agriculture people and industries where wireless pump and motor control required.Our GSM based mobile pump controller is manufactured with advanced micro controller technology and quality process. Yet these devices are affordable to customer.

 

Advantages of Wireless Pump Controller

•    User can operate pump/motor from anywhere, from any distance.
•    User can operate pump via SMS as well as just Missed Call.
•    GSM Technology, Reliable operation, Worldwide Connectivity.
•    Low Cost, Quality and less maintenance and robust device.
•    Storing Master’s No  AND Slave upto 10 Mobile Nos  Through SMS.
•    SMS to Get the Status of device.
•    Missed Call To Control - Motor On and Off.
•    Message Alerts for Power UP, Motor On, Motor Off, Status.

 

Specification

•    Board working Voltage is 12VAC/DC min 1.5 amps.
•    External High Gain Antenna with Kit Included.
•    SIM card Slot Backside of PCB.

Additional Information:

• Item Code: SEES-1278
• Production Capacity: 1000 NOS
• Delivery Time: 1-2 DAYS
• Packaging Details: CARTOON BOXES

Product description

 

FEATURES

High reliability and Low maintenance. Automatic SEES Water Level Controller SEES-Sump can be used for a long time, no maintenance or repairing would be Required during its operational period. Low AC Voltage sensing circuit to avoid polarization of electrodes in water. These special stainless steel plastic SEES molded conductive electrodes are Long life sensors and do not require frequent cleaning or replacement. Overflow prevention system provides effective and reliable Water level monitoring, with Level Indicators.

Rocker Bypass Switch.

The optional rocker switch is provided to bypass system operation in case of system failure. so no need to disconnect the system when it gets failed.

DryRun

Due to faulty foot valve or air leakage in the pipe if the motor runs dry then it gets switched off automatically and gives fault indication. For more details please watch video demo.

VoltageCut-off

Automatic Water Level Controller SEES-S automatically switches-off the pump if the supply voltage drops below 160V or Crosses 250V.

 

Sutable for

mono block pump (sump motor)
sump submersible pumps.
Jet Pumps, etc...

This Water level controllers Indicator is highly recommended for metro cities or areas where drinking water is supplied through pipelines which are further distributed in homes, hotels, societies etc.

At large our systems not only help you but your neighbours and society, also as it reduces the wastage of water by cutting down any further overflow than what you need.

 

AUTOMATIC WATER LEVEL CONTROLLER(SUMP)
•When overhead tank goes 20% pump starts automatically and when tank full automatic pump will turn off
•If sump tank also empty pump will turn off
•Dry run also available, if checks a water flow for one minute if water not flowing more than a minute pump will goes off.
•Water does not waste, and we can save electricity, and our precious time.
•SS contact sensor type.
•Microcontroller based controlling Applications: Home, School, Hospital, Industries, College.

 

SPECIFICATION POWER INPUT :
•230v input
•12v-1A Transformer
•When the power on red led will glow RELAY :
•12v T relay: 250v 30A, 24v 30A
•Relay used :1 Channel SENSOR PINS:
•Common (com), Sump Low(SL), Sump High (SH), Tank Low (TL), Tank High (TH), Dry run (DR). SENSOR TYPE:
•SS Contact type

• Model Name/Number SEES-SUMP
• Operation Type Fully Automatic Phase 1-Phase
• Range 3.1-5m, 0-3m
• Features Corrosion Resistant, Low Temperature Resistant
• Usage/Application Water Level Controller
• Input Voltage 160V - 250V
• Size 170mm x150mm x 60mm
• Warranty 1 Year
• Dry run trip delay 90 seconds.
• Power onDelay 30 seconds
• Frequency 50 Hz

Additional Information:

• Item Code: SEES-1265
• Production Capacity: 1000 nos
• Delivery Time: 1-2 DAYS
• Packaging Details: CARTOON BOXES

FEATURES

High reliability and Low maintenance. Automatic SEES Mini Automatic Water Level Controller-Sump -Single phase can be used for a long time, no maintenance or repairing would be Required during its operational period. Low AC Voltage sensing circuit to avoid polarization of electrodes in water. These special stainless steel plastic SEES molded conductive electrodes are Long life sensors and do not require frequent cleaning or replacement. Overflow prevention system provides effective and reliable Water level monitoring, with Level Indicators.

Rocker Bypass Switch.

The optional rocker switch is provided to bypass system operation in case of system failure. so no need to disconnect the system when it gets failed.

DryRun

Due to faulty foot valve or air leakage in the pipe if the motor runs dry then it gets switched off automatically and gives fault indication. For more details please watch video demo.

VoltageCut-off

Automatic Water Level Controller SEES-S automatically switches-off the pump if the supply voltage drops below 160V or Crosses 250V.

 

Sutable for

mono block pump (sump motor)
sump submersible pumps.
Jet Pumps, etc...

This Water level controllers Indicator is highly recommended for metro cities or areas where drinking water is supplied through pipelines which are further distributed in homes, hotels, societies etc.

At large our systems not only help you but your neighbours and society, also as it reduces the wastage of water by cutting down any further overflow than what you need.

 

AUTOMATIC WATER LEVEL CONTROLLER(SUMP)
•When overhead tank goes 20% pump starts automatically and when tank full automatic pump will turn off
•If sump tank also empty pump will turn off
•Dry run also available, if checks a water flow for one minute if water not flowing more than a minute pump will goes off.
•Water does not waste, and we can save electricity, and our precious time.
•SS contact sensor type.
•Microcontroller based controlling Applications: Home, School, Hospital, Industries, College.

 

SPECIFICATION POWER INPUT :
•230v input
•12v-1A Transformer
•When the power on red led will glow RELAY :
•12v T relay: 250v 30A, 24v 30A
•Relay used :1 Channel SENSOR PINS:
•Common (com), Sump Low(SL), Sump High (SH), Tank Low (TL), Tank High (TH), Dry run (DR). SENSOR TYPE:
•SS Contact type

• Model Name/Number SEES-SUMP
• Operation Type Fully Automatic Phase 1-Phase
• Range 3.1-5m, 0-3m
• Features Corrosion Resistant, Low Temperature Resistant
• Usage/Application Water Level Controller
• Input Voltage 160V - 250V
• Warranty 1 Year
• Dry run trip delay 90 seconds.
• Power onDelay 30 seconds
• Frequency 50 Hz

 

Additional Information:

• Item Code: SEES-1277
• Production Capacity: 1000 nos
• Delivery Time: 1-2 DAYS
• Packaging Details: CARTOON BOXES

Product description

 

SEES Automatic Water Level Controller-Sump-Single phase- 2 Tank model

FEATURES

High reliability and Low maintenance. Automatic SEES Water Level Controller SEES-Sump can be used for a long time, no maintenance or repairing would be Required during its operational period. Low AC Voltage sensing circuit to avoid polarization of electrodes in water. These special stainless steel plastic SEES molded conductive electrodes are Long life sensors and do not require frequent cleaning or replacement. Overflow prevention system provides effective and reliable Water level monitoring, with Level Indicators.

Rocker Bypass Switch.

The optional rocker switch is provided to bypass system operation in case of system failure. so no need to disconnect the system when it gets failed.

DryRun

Due to faulty foot valve or air leakage in the pipe if the motor runs dry then it gets switched off automatically and gives fault indication. For more details please watch video demo.

VoltageCut-off

Automatic Water Level Controller SEES-S automatically switches-off the pump if the supply voltage drops below 160V or Crosses 250V.

 

Sutable for

mono block pump (sump motor)
sump submersible pumps.
Jet Pumps, etc...

This Water level controllers Indicator is highly recommended for metro cities or areas where drinking water is supplied through pipelines which are further distributed in homes, hotels, societies etc.

At large our systems not only help you but your neighbours and society, also as it reduces the wastage of water by cutting down any further overflow than what you need.

 

AUTOMATIC WATER LEVEL CONTROLLER(SUMP)
•When overhead tank goes 20% pump starts automatically and when tank full automatic pump will turn off
•If sump tank also empty pump will turn off
•Dry run also available, if checks a water flow for one minute if water not flowing more than a minute pump will goes off.
•Water does not waste, and we can save electricity, and our precious time.
•SS contact sensor type.
•Microcontroller based controlling Applications: Home, School, Hospital, Industries, College.

 

SPECIFICATION POWER INPUT :
•230v input
•12v-1A Transformer
•When the power on red led will glow RELAY :
•12v T relay: 250v 30A, 24v 30A
•Relay used :1 Channel SENSOR PINS:
•Common (com), Sump Low(SL), Sump High (SH), Tank Low (TL), Tank High (TH), Dry run (DR). SENSOR TYPE:
•SS Contact type

• Model Name/Number SEES-SUMP- 2 tank model
• Operation Type Fully Automatic Phase 1-Phase
• Range 3.1-5m, 0-3m
• Features Corrosion Resistant, Low Temperature Resistant
• Usage/Application Water Level Controller
• Input Voltage 160V - 250V
• Size 170mm x150mm x 60mm
• Warranty 1 Year
• Dry run trip delay 90 seconds.
• Power onDelay 30 seconds
• Frequency 50 Hz

Additional Information:

• Item Code: SEES-1287
• Production Capacity: 1000 NOS
• Delivery Time: 2-3 DAYS
• Packaging Details: CARTOON BOXES

 

 

FEATURES

High reliability and Low maintenance. Automatic SEES Water Level Controller SEES-Sump can be used for a long time, no maintenance or repairing would be Required during its operational period. Low AC Voltage sensing circuit to avoid polarization of electrodes in water. These special stainless steel plastic SEES molded conductive electrodes are Long life sensors and do not require frequent cleaning or replacement. Overflow prevention system provides effective and reliable Water level monitoring, with Level Indicators.

Rocker Bypass Switch.

The optional rocker switch is provided to bypass system operation in case of system failure. so no need to disconnect the system when it gets failed.

DryRun

Due to faulty foot valve or air leakage in the pipe if the motor runs dry then it gets switched off automatically and gives fault indication. For more details please watch video demo.

VoltageCut-off

Automatic Water Level Controller SEES-S automatically switches-off the pump if the supply voltage drops below 160V or Crosses 250V.

 

Sutable for

 mono block pump (sump motor)
 sump submersible pumps.
 Jet Pumps, etc...
This Water level controllers Indicator is highly recommended for metro cities or areas where drinking water is supplied through pipelines which are further distributed in homes, hotels, societies etc.

At large our systems not only help you but your neighbours and society, also as it reduces the wastage of water by cutting down any further overflow than what you need.

 

 

Additional Information:

• Item Code: SEES-5025
• Production Capacity: 1000 NOS
• Delivery Time: 1-2 DAYS
• Packaging Details: CARTOON BOXES

FEATURES

High reliability and Low maintenance. Automatic SEES Water Level Controller SEES-Sump can be used for a long time, no maintenance or repairing would be Required during its operational period. Low AC Voltage sensing circuit to avoid polarization of electrodes in water. These special stainless steel plastic SEES molded conductive electrodes are Long life sensors and do not require frequent cleaning or replacement. Overflow prevention system provides effective and reliable Water level monitoring, with Level Indicators.

Rocker Bypass Switch.

The optional rocker switch is provided to bypass system operation in case of system failure. so no need to disconnect the system when it gets failed.

DryRun

Due to faulty foot valve or air leakage in the pipe if the motor runs dry then it gets switched off automatically and gives fault indication. For more details please watch video demo.

VoltageCut-off

Automatic Water Level Controller SEES-S automatically switches-off the pump if the supply voltage drops below 160V or Crosses 250V.

 

Sutable for

 mono block pump (sump motor)
 sump submersible pumps.
 Jet Pumps, etc...
This Water level controllers Indicator is highly recommended for metro cities or areas where drinking water is supplied through pipelines which are further distributed in homes, hotels, societies etc.

At large our systems not only help you but your neighbours and society, also as it reduces the wastage of water by cutting down any further overflow than what you need.

Additional Information:

• Item Code: SEES-5020
• Port of Dispatch: Coimbatore
• Production Capacity: 1000
• Delivery Time: 2-3days
• Packaging Details: CARTOON BOXES

FEATURES

High reliability and Low maintenance. Automatic SEES Water Level Controller SEES-Sump can be used for a long time, no maintenance or repairing would be Required during its operational period. Low AC Voltage sensing circuit to avoid polarization of electrodes in water. These special stainless steel plastic SEES molded conductive electrodes are Long life sensors and do not require frequent cleaning or replacement. Overflow prevention system provides effective and reliable Water level monitoring, with Level Indicators.

Rocker Bypass Switch.

The optional rocker switch is provided to bypass system operation in case of system failure. so no need to disconnect the system when it gets failed.

DryRun

Due to faulty foot valve or air leakage in the pipe if the motor runs dry then it gets switched off automatically and gives fault indication. For more details please watch video demo.

VoltageCut-off

Automatic Water Level Controller SEES-S automatically switches-off the pump if the supply voltage drops below 160V or Crosses 250V.

 

Sutable for

 mono block pump (sump motor)
 sump submersible pumps.
 Jet Pumps, etc...
This Water level controllers Indicator is highly recommended for metro cities or areas where drinking water is supplied through pipelines which are further distributed in homes, hotels, societies etc.

At large our systems not only help you but your neighbours and society, also as it reduces the wastage of water by cutting down any further overflow than what you need.

Additional Information:

• Item Code: SEES-5023
• Production Capacity: 1000 NOS
• Delivery Time: 1-2 DAYS
• Packaging Details: CARTOON BOXES

• Automatic Water Level Controller -Sump/ Bore-3 Phase system
• The underground tank or sump, motor get start automatically. The tank starts filling up. when the water level reaches to the higher level, the motor automatically gets switched off.
• AUTO OFF WHEN TANK IS FULL OR SUMP IS EMPTY.
• This model have dry run protection so it only start motor if water present in underground tank or sump.
• Suitable to any HP Motor as no load comes on our controller. Load passes to existing starter.
• Motor ON OFF LED indication provided.
• Water Level indication provided for both tank and sump.
• Supply voltage : 415 V AC,

• Sensing element : ss  contact type sensor, it is free from oxidation, long life. Any conducting wire can be use for sensor.

  Auto and Manual mode switch available. In auto mode motor start and stop automatically. 

  High quality M.S. enclosure provided.

  Fully automatic, controls from underground tank to overhead tank so no man power required. Long service Life.

• In manual mode user can start and stop motor by pressing start and stop button of controller. 

• No additional wiring require to operate motor manually.

Additional Information:

• Item Code: SEES-5027
• Production Capacity: 1000 NOS
• Delivery Time: 2-3 DAYS
• Packaging Details: CARTOON BOXES

BOREWELL TO OVERHEAD TANK (SEES-BORE)

Automatic Water Level Controller For Single Phase Submersible (bore well) Pumps Panel Driver (Single phase tothree phase). This is a unique device for submersible Pump Up to 2.5 HP Capacity. Our submersible panel drive is the most suitable device for start/Run capacitors Panel Driven Water Pumps. It increases the life of motor to work for year. Application Like Residential Buildings, apartment’s, Commercial Complexes, Industrial Buildings, Hotels, Hospitals, . . . .Etc.

Visual Indications :

Four stage water level indicator for over head tank, water flow indication(Running Line), voltage level indication, power on indication and auto/manual indication.

 

Features: Switch on the panel if water tank is in required mode and switch off the panel at tank full.

Dry Run
Due to faulty foot valve or air leakage in the pipe if the motor runs dry then it gets switched off
automatically and gives fault indication.

Voltage Cut-off
Automatic Water Level Controller SEES-BORE automatically switches-off the pump if the supply voltage drops below 160V or Crosses 250V.

 

Surge protection
Built in surge protection is the Main features of SEES series.

Toggle Bypass Switch.
The optional toggle switch is provided to bypass system operation in case of system failure. so no need to disconnect the system when it gets failed.

Power ON/OFF Switch.
Small rocker switch to select Power On/Off operation.

Application:
The product is suitable for almost all site conditions water tank for maintaining level
automatically, can be used to control water inflow or outflow, by means of direct pump control or acting as a control switch of a magnetic or combination starter.

Sutable for

 

 Bore well submersible pumps.
 Jet Pumps,
In SEES series variants are available for any type of pump, bore well and any combination of tanks.

Additional Information:

• Item Code: SEES-5012
• Port of Dispatch: Coimbatore
• Production Capacity: 1000
• Delivery Time: 1-2days
• Packaging Details: CARTOON BOXES

Benefits :

• No Tension of Water Overflow.
• No Power Wastage, No Water Wastage.
• Overhead Tank always remains Water.
• 4 Level Water Indicators – 25%, 50%, 75% 100% of Water Tank Levels.

This Model indicates 5 levels of overhead tank only. If water reaches 100% of OVER HEAD TANK this model gives continuous alarm directing to put OFF the motor & if water comes below 25% of OVER HEAD TANK, it gives continuous alarm directing to put on the motor. To put OFF the alarm, Press MUTE soft touch button.

Additional Information:

• Item Code: SEES-5028
• Production Capacity: 1000 NOS
• Delivery Time: 1-2 DAYS
• Packaging Details: CARTOON BOXES

Water Contact sensor

• Useful for Water level Controller based on contact types
• Stainless Steel Rods ( No rust will occur even for hard water)
• Easy to tie using tags

SS316 contact type Water level sensor used to detect presence of water in water tank, water cooler or sump tanks

Additional Information:

• Item Code: SEES-1486
• Port of Dispatch: Coimbatore
• Production Capacity: 1000
• Delivery Time: 1-2days
• Packaging Details: cartoon boxes