Sri Electronics & Embedded Solutions

ISO Certification Course on Design of Embedded System using Arduino UNO R3

Theory Concepts:

• Introduction to Arduino UNO R3
• Introduction to Arduino Software
• Features of Arduino UNO R3
• Architecture, Pin Diagram
• Memory Organization
• Instruction set
• I/O Ports Configuration
• Analog To Digital Converter (ADC)
• Capture Compare PWM Module (CCP)
• UART Communications
• MSSP ( SPI and I2C)
• I2C RTC & SPI EEPROM

Practical Session:

• Interfacing LED(Light Emitting Diode)
• Interfacing Switch with LED
• Interfacing 7-Segment Display
• Interfacing 7-Segment Display with Switch
• Interfacing Relay with Switch
• Interfacing LCD(16×2) in 8 bit mode and 4 bit mode
• Interfacing LCD with Switch
• Interfacing Stop Watch with LCD
• Interfacing EEPROM to Read and Write the data
• Interfacing PWM with LED
• Interfacing I2C with LCD to Display RTC
• Interfacing ADC with Sensor(Pot 10k,LM35,Proximity)
• Interfacing Stepper Motor with Forward and Reverse Rotation using L298 Driver.
• Interfacing DC Motor with Forward and Reverse Rotation using L298 Driver
• Interfacing Matrix Keypad(4×4) with LCD
• Interfacing UART with both Transmit and Receive
• Interfacing GSM(SIM900A) to send a message
• Interfacing RF(Radio Frequencies 433MHZ) to Wireless Communication

Course Highlights:

• We will provide development board at free of cost
• Industrial Trainers
• Case study
• Hands-On Training
• Project Guidance
• Tutorial and necessary documents
• Compiler and Simulator student version

ISO Certification Course on Embedded Robotics

Theory Concepts:

• Introduction to Arduino UNO R3
• Introduction to Arduino Software
• Features of Arduino UNO R3
• Architecture, Pin Diagram
• Memory Organization
• Instruction set
• I/O Ports Configuration

Practical Session:

• DTMF Controlled Robot with Microcontroller
• Microcontroller based line following Robot
• Metal Detector Robot using Microcontroller
• Obstacle Avoiding Robot
• Bluetooth Control Robot using Android Phone
• Automatic Fire Sensing and Extinguishing Robot
• Automatic Wall Painting Robot
• Remote Controlled Pick and Place Robot
• Voice Controlled Robotic Vehicle
• Design of Surface cleaning robot
• IR Controlled Robotic vehicle
• Fire Fighting Robotic Vehicle using Microcontroller
• PC Controlled Human Detection Robot
• Radio Frequency (RF) Controlled Wireless Robot
• GSM (SMS) Mobile Phone Controlled Intelligent Robot

Course Highlights:

• We will provide Robotic kits at free of cost
• Industrial Trainers
• Case study
• Hands-On Training
• Project Guidance
• Tutorial and necessary documents
• Compiler and Simulator student version

• Introduction to PIC Family of MCUs
• Introduction to MPLAB IDE & HiTech C
• Basic Structure of C programs
• Introduction to Embedded C
• Features of PIC16F877A
• Architecture, Pin Diagram
• Memory Organization
• Instruction set
• I/O Ports Configuration
• Analog To Digital Converter (ADC)
• Timers Timer0,1 and 2
• Capture Compare PWM Module (CCP)
• UART Communications
• Basic embedded C programming and its Concepts
  • i) LED Interfacing with PIC 16F877A
  • ii) LED and Switch Interfacing with PIC 16F877A
  • iii) 7-SEGMENT display Interfacing with PIC 16F877A
  • iv) 7-Segment and switch Interfacing with PIC 16F877A
  • v) Relay Interfacing with PIC 16F877A

• Registered Certification will be given to candidates
• Industrial Trainers
• Case study
• Hands-On Training
• Project Guidence
• Tutorial and necessary documents
• Compiler and Simulator student version

ISO Certification Course on Design of Embedded System using PIC MCU

Theory Concepts:

• Introduction to PIC MCU
• Introduction to MPLAB IDE and Hi-Tech Compiler
• Introduction to PIC KIT 2 Programmer/Debugger
• Introduction to Proteus 8
• Features of PIC16F877A
• Architecture, Pin Diagram
• Memory Organization
• Instruction set
• I/O Ports Configuration
• Analog To Digital Converter (ADC)
• Timers Timer0,1 and 2
• Capture Compare PWM Module (CCP)
• UART Communications
• Interrupts(Software and Hardware)
• MSSP ( SPI and I2C)
• I2C RTC & SPI EEPROM

Practical Session:

• Interfacing LED(Light Emitting Diode)
• Interfacing Switch with LED
• Interfacing 7-Segment Display
• Interfacing 7-Segment Display with Switch
• Interfacing Relay with Switch
• Interfacing LCD(16×2) in 8 bit mode and 4 bit mode
• Interfacing LCD with Switch
• Interfacing Stop Watch with LCD
• Interfacing EEPROM to Read and Write the data
• Interfacing PWM with LED
• Interfacing I2C with LCD to Display RTC
• Interfacing ADC with Sensor(Pot 10k,LM35,Proximity)
• Interfacing Stepper Motor with Forward and Reverse Rotation using L298 Driver.
• Interfacing DC Motor with Forward and Reverse Rotation using L298 Driver
• Interfacing Matrix Keypad(4×4) with LCD
• Interfacing UART with both Transmit and Receive
• Interfacing GSM(SIM900A) to send a message
• Interfacing RF(Radio Frequencies 433MHZ) to Wireless Communication

Course Highlights:

• We will provide development board at free of cost
• Industrial Trainers
• Case study
• Hands-On Training
• Project Guidance
• Tutorial and necessary documents
• Compiler and Simulator student version