Sri Electronics & Embedded Solutions

It Is Ideal For Hobbyists, School / College, And Engineering Students. Widely Used For Electronic Projects.*This PCB can almost be seen in electronic equipment like electronic watches, calculators, computers, communication electronic equipment, military weapon system, etc

Additional Information:

• Item Code: SEES-5991
• Production Capacity: 1000 nos
• Delivery Time: 3-4 days
• Packaging Details: CARTOON BOXES

A breadboard is an invaluable tool for experimenting with circuit designs whether in the R and D or university lab. A breadboard is used to make up temporary circuits for testing or to try out an idea. No soldering is required so it is easy to change connections and replace components. Parts will not be damaged so they will be available for re-use afterwards.
840 Tie Points - 128 Groups Of 5 Connected Terminals, 8 Bus Of 25 Connected Terminals.

• Adhesive sheet on the back side of the board - multiple breadboards can be spliced together too
• Fit for jumper wire of 0.8 mm diameter - standard 2.54 mm hole spacing
• Reusable for fast build a prototype of an electronic circuit - will accept transistors, diodes, LED's, resistors, capacitors and virtually all types of components - no soldering required - can modify or revise the circuits easily

Additional Information:

• Item Code: SEES-5985
• Production Capacity: 1000 nos
• Delivery Time: 3-4 days
• Packaging Details: CARTOON BOXES

Solderless breadboard withh 400 tie point. It has 2 power buses, 10 columns, and 30 rows. All pins are spaced by a standard 0. 1Andquot.. The two sets of five columns are separated by about 0. 3Andquot., perfect for straddling a dip package over.

• Perfect for Arduino shield prototyping and testing
• Accept wire with diameter20-29awg
• Voltage/current: 300v/3-5

Additional Information:

• Item Code: SEES-5986
• Production Capacity: 1000 nos
• Delivery Time: 3-4 days
• Packaging Details: CARTOON BOXES

An MB102 830 Points Solderless Prototype PCB Breadboard is an invaluable tool for experimenting with circuit designs whether in the R&D or university lab. A breadboard is used to make up temporary circuits for testing or to try out an idea. No soldering is required so it is easy to change connections and replace components.

Additional Information:

• Item Code: SEES-5984
• Production Capacity: 1000 nos
• Delivery Time: 3-4 days
• Packaging Details: CARTOON BOXES

Reusable for fast build a prototype of an electronic circuit will accept transistors, diodes, LEDS, resistors, capacitors and virtually all types of components*Adhesive sheet on the back side of the board, multiple breadboards can be spliced together too*No soldering required or can modify or revise the circuits easily, fit for jumper wire of 0.8mm diameter standard 2.54mm hole spacing

Additional Information:

• Item Code: SEES-5987
• Production Capacity: 1000 nos
• Delivery Time: 3-4 days
• Packaging Details: CARTOON BOXES

It is copper wires which used for connection between terminals & devices.
A jump wire (also known as jumper wire, or jumper) is an electrical wire, or group of them in a cable, with a connector or pin at each end (or sometimes without them – simply “tinned”), which is normally used to interconnect the components of a breadboard or other prototype or test circuit, internally or with other …

Additional Information:

• Item Code: SEES-5989
• Production Capacity: 1000 nos
• Delivery Time: 3-4 days
• Packaging Details: CARTOON BOXES

Built-in protection against short-circuit through power limiting circuitry compatible with 5V, 3.3V, Input Voltage :6.5-12V (DC) or USB power, Output voltage: 3.3V, 5V switchable

Additional Information:

• Item Code: SEES-5990
• Production Capacity: 1000 nos
• Delivery Time: 3-4 days
• Packaging Details: CARTOON BOXES

This mini breadboard is convenient for the prototypes and circuit design experiment. With breadboard jumpers wires, this solderless breadboard is perfect for electronic DIY.This small breadboard is 170 tie-points total: 2 columns of 17 lines, 5 points at each line, they are easy to be fixed with breadboard jumper wires, easy to use breadboard holder. The solderless breadboards do not require soldering, so they are completely re-usable.-This tiny breadboard is made of ABS plastic, with the metal inside the bread board, jumper wires are easy to insert into or remove from these breadboards. 170 tie points breadboards are with the self-adhesive tape on the back, make them easy to stick on the prototype shield or a flat surface.Dimension:1.85inchx1.38inchx0.33inch or 4.7cmx3.5cmx8.5cm. With nubbins and slots on the sides of 170 points breadboard.Color: white

Additional Information:

• Item Code: SEES-5988
• Production Capacity: 1000 nos
• Delivery Time: 3-4 days
• Packaging Details: CARTOON BOXES